Panasonic AFP7CPS4E Скачать руководство пользователя страница 18

Страница: 18 / 139

Functions of Units and Restrictions on Combination

1-8

1.3 Restrictions on Units Combination

1.3.1 Restrictions on the Number of Installed Units

There are following restrictions depending on units to be used.

Unit type

Number of installed units

Remarks

Serial Communication Unit

Max. 8 units

1.3.2 Restrictions on the Combination of Extension Cassettes

(Communication Cassettes)



One communication cassette can be attached to the CPU unit, and two communication

cassettes to the serial communication unit.



The FP7 communication cassette (Ethernet type) can be attached to the CPU only. It cannot

be attached to the serial communication unit (SCU).

1.3.3 Restrictions on Communication Functions to be Used

There are the following restrictions on functions to be used when using the SCU or ET-LAN
that is built in the CPU unit, or the serial communication unit (SCU).

Function to be used

Restrictions

PLC link function

Up to two communication ports can be used. For using two ports, allocate
different link areas to them.

CPU with built-in SCU (COM.1 port)

Serial communication unit (COM.1 port)

MEWTOCOL-COM master

MODBUS-RTU master

A maximum of 16 communication ports and the number of connections in
combination can be used simultaneously.

CPU with built-in SCU (COM.1 port to COM. 2 port)

Serial communication unit (COM.1 port to COM.4 port)

CPU with built-in ET-LAN (User connections 1 to 16)

MEWTOCOL-COM slave

MEWTOCOL7-COM slave

MODBUS-RTU slave

A maximum of 15 communication ports and the number of connections in
combination can be used simultaneously.

CPU with built-in SCU (COM.1 port to COM. 2 port)

Serial communication unit (COM.1 port to COM.4 port)

CPU with built-in ET-LAN

(System connections 1 to 4 / User connections 1 to 16)

General-purpose
communication

There is no restriction.

1.3.4 Unit to be Used and Applicable Versions of CPU Unit and FPWIN GR7

For using the unit, the following versions of CPU unit and FPWINGR7 are required.

Applicable versions

Unit type

CPU unit

FPWINGR7

Remarks

FP7 Serial Communication Unit

Ver.1.2 or later

Ver.1.3 or later

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7CPS4E












































































































































Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды

Panasonic AFP7CPS4E, Руководство пользователя

Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды