Panasonic AFP7CPS4E Скачать руководство пользователя страница 55

Страница: 55 / 139

5.2 Setting Communication Conditions

5-3

5.2 Setting Communication Conditions

5.2.1 Settings Using FPWIN GR7 (For CPU with built-in SCU)

Applications and communication conditions for each communication port should be set using
the tool software FPWIN GR7.

PROCEDURE

1. From the menu bar, select "Option" > "FP7 Configuration".

The "FP7 Configuration" dialog box opens.

2. Select "Built-in SCU".

Setting items for "Built-in SCU" appear.

3. Specify communication conditions and press [OK] button.

Set conditions are incorporated into the project that is being edited.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7CPS4E












































































































































Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды

Panasonic AFP7CPS4E, Руководство пользователя

Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды