Panasonic AFP7CPS4E Скачать руководство пользователя страница 119

Страница: 119 / 139

10.2

What to DO If an Error Occurs

(For Each Communication Mode)

10-5

10.2.3 When Using General-purpose Communication Function



What to do if an error occurs

Situation

Contents to check

Confirmation method

Is a communication cassette attached?

Check if the communication block is
installed firmly.

Are wirings correct?

Check the wirings again.

Isn't there any problem in environments such as
noise?

Check the shielding.

Communication is not
possible.
(For the serial
communication unit, the
ERROR LED turns on.)

Is the communication mode set correctly?

・

Check the configuration (COM

settings) of the CPU with built-in SCU
or the serial communication unit.

・

Check the communication

parameters with PMGET instruction.
(Note)

Transmission is not
possible.
(For the serial
communication unit, the
ERROR LED turns on.)

Does an operation error occur when GPSEND
instruction is executed?

Isn't transmission prohibited by CTS signal (Y14
or Y16) when using a communication cassette
with RS-232C (5-wire type)?

Review the program.

Is the setting for the communication conditions
the same as the one for the device
communicated?

Transmission is not
possible.

Is the setting of the method for detecting
“reception done” the same as the one for the
device communicated?

・

Check the configuration (COM

settings) of the CPU with built-in SCU
or the serial communication unit.

・

Check the communication

parameters with PMGET instruction.
(Note)

Isn't reception error occurring?

Isn't the reception buffer FULL error occurring?
If the error occurs, the operation cannot be
restarted without performing channel reset.

Reception is not possible.
(For the serial
communication unit, the
ERROR LED turns on.)

Isn't the operation mode set to a mode other
than general-purpose communication with
PMSET instruction?

・

Check the communication

parameters and operation status
monitor information with PMGET
instruction. (Note)

(Note) For checking communication parameters with PMGET instruction, the CPU should be set in the RUN mode.

Set "Mode selection when self-diagnostic error occurs - A unit error occurred." to "Continue operation" in the
CPU configuration.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7CPS4E












































































































































Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды

Panasonic AFP7CPS4E, Руководство пользователя

Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды