manualshive.com logo in svg

Palax Power 100S, Руководство по эксплуатации

Поделиться
Скачать
Palax Power 100S Скачать руководство пользователя страница 24

Palax Power 100S 

Translation 

 

       

 

 

1-2017

 

24 

 

 

Never leave the machine, which is easy to start, unattended.  

 

5.4  Operating the crosscut saw, before the operation 

Clean any protective grease off the new circular saw-blade, because a greasy blade accu-
mulates resin easily, causing it to get hot, lose its tension and change  shape. 

 

 

5.5  During the operation 

 

Exercise caution, always keep your hands away from the saw-blade. 

 

Never stop the rotation of the blade by pressing wood against it. 

 

During the cut-off operation, make sure that the tree always leans against the support 
roller at the cutting point. 

 

5.6  Placing the wood on the deck 

 

Place the log on the deck so that  it touches the wall behind the conveyor. Otherwise, 
the log may move during cutting. 

 

Exercise particular caution when cutting crooked logs. 

 

WARNING!   

Crooked logs might be turned on the deck by the cutting force, 

thus twisting the blade so strongly that it breaks. 

 

5.7 Crosscut 

operation 

 

Pull the control lever of the hydraulic valve backward to bring the saw-blade down and  

 

cut through the wood. 

 

Be especially careful when you cut knotty or crooked trees. 

Speed control 

 

Fig. 20 

 

The machine is equipped with lowering speed control for the crosscut saw-blade. If you 
want to speed up or slow down the crosscut saw-blade's lowering speed, adjust the valve 
in either (+) or (-) direction. 

 

Содержание Power 100S






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды