Packard Bell EasyNote LJ75 Скачать руководство пользователя

Страница: 53 / 222

Chapter 2

Remove HDD/BIOS Password Utilities

This section provides you with details about removing HDD/BIOS password:

Remove HDD Password:

If you key in the wrong HDD password three times, an error is generated.

To reset the HDD password, perform the following steps:

After the error is displayed, select the

Enter Unlock Password

option on the screen.

An Encode key is generated for unlocking utilities. Note down this key.

Execute the

UnlockHD.EXE

file to create the unlock code in DOS Mode using the format

UnlockHD

[Encode code]

with the code noted in the previous step, as follows:

UnlockHD 76943488

The command generates a password which can be used for unlocking the HDD.

Password: 46548274

Key in the password from the previous step to unlock the HDD as shown.

All manuals and user guides at all-guides.com

Содержание Bell EasyNote LJ75































































































































































































































Результаты поиска

Содержание Bell EasyNote LJ75

Отзывы:

Похожие инструкции для Bell EasyNote LJ75

Бренды по названию

Популярные бренды

Packard Bell EasyNote LJ75, Руководство по обслуживанию

Результаты поиска

Содержание Bell EasyNote LJ75

Отзывы:

Похожие инструкции для Bell EasyNote LJ75

Бренды по названию

Популярные бренды