Packard Bell EasyNote LJ75 Скачать руководство пользователя

Страница: 167 / 222

Chapter 4

157

Thermal Unit Failure

If the

Thermal

Unit

fails, perform the following actions one at a time to correct the problem. Do not replace

non-defective FRUs:

External Mouse Failure

If an external

Mouse

fails, perform the following actions one at a time to correct the problem.

Try an alternative mouse.

If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See
the mouse user manual.

If the mouse uses a USB connection, try an alternate USB port.

Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.

START

Fan power

wire well

connected?

Connect it well

Fan OK?

Replace

thermal

module

Seat it well

Replace

CPU

Replace M/B

CPU

heatsink well

seated?

CPU OK?

All manuals and user guides at all-guides.com

Содержание Bell EasyNote LJ75































































































































































































































Результаты поиска

Содержание Bell EasyNote LJ75

Отзывы:

Похожие инструкции для Bell EasyNote LJ75

Бренды по названию

Популярные бренды

Packard Bell EasyNote LJ75, Руководство по обслуживанию

Результаты поиска

Содержание Bell EasyNote LJ75

Отзывы:

Похожие инструкции для Bell EasyNote LJ75

Бренды по названию

Популярные бренды