Packard Bell EasyNote LJ75 Скачать руководство пользователя

Страница: 157 / 222

Chapter 4

147

Internal Microphone Failure

If the internal

Microphone

fails, perform the following actions one at a time to correct the problem. Do not

replace non-defective FRUs:

Microphone Problems

If internal or external

Microphones

do no operate correctly, perform the following actions one at a time to

correct the problem.

Check that the microphone is enabled. Navigate to

Start

Control

Panel

Hardware

and

Sound

and select the

Recording

tab.

Right-click on the

Recording

tab and select

Show

Disabled

Devices

(clear by default).

The microphone appears on the

Recording

tab.

Right-click on the microphone and select

Enable

Select the microphone then click

Properties

. Select the

Levels

tab.

Increase the volume to the maximum setting and click

Test the microphone hardware:

Select the microphone and click

Configure

Select

Set up microphone

Select the microphone type from the list and click

Next

Follow the onscreen prompts to complete the test.

If the Issue is still not resolved, see “Online Support Information” on page 207.

Start

Check M/B

Mic cable

Re-assemble

the MIC cable

to M/B

Check MIC

wire of LCD

module

Swap MIC wire
of LCD module

Swap M/B

All manuals and user guides at all-guides.com

Содержание Bell EasyNote LJ75































































































































































































































Результаты поиска

Содержание Bell EasyNote LJ75

Отзывы:

Похожие инструкции для Bell EasyNote LJ75

Бренды по названию

Популярные бренды

Packard Bell EasyNote LJ75, Руководство по обслуживанию

Результаты поиска

Содержание Bell EasyNote LJ75

Отзывы:

Похожие инструкции для Bell EasyNote LJ75

Бренды по названию

Популярные бренды