manualshive.com logo in svg

Pacific energy FP25AR, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pacific energy FP25AR Скачать руководство пользователя страница 16

Offsets

30

° or 

45

°

 ELBOWS

The chimney for the FP25 can be installed with a maximum 

of four 45° elbows(in Canada) and four 30° elbows(in 

U.S.A.) as shown in Fig. #10.

Installation:

1.   NOTE: Install the first elbow and turn it in the required 

direction.  

2.   Install  the  necessary  chimney  lengths  to  achieve  the 

required  offset.  Lock  the  chimney  lengths  together 

according  to  the  chimney  manufacturer’s  instructions. 

If the offset length is made of two (2) chimney lengths 

or more, many chimney manufacturers may require that 

you use an offset or roof support halfway up the offset. If 

penetrating a wall, install a wall radiation shield supplied 

by the chimney manufacturer and install according to the 

manufacturer's instructions.

3.  Use  another  elbow  to  turn  the  chimney  vertically  and 

secure the elbow.

4.  Use a plumb bob to line up the centre of the hole with the 

center of the flue collar on the fireplace. Cut a hole for the 

chimney in the ceiling/floor. Frame the hole as described 

on page 15.

5.  Install  a  firestop  following  the  chimney  manufacturer's 

directions.

6.  Follow  the  chimney  manufacturer's  guidelines  for 

supporting the offsets. Reminder - The chimney must be 

supported after the first 20'(6.1m).

Fig. #10

NOTE: IT IS REqUIRED ThAT ALL 

ChIMNEy SySTEM CONNECTIONS BE 

SECURED WITh (3)-#8 x ½"(12 MM) 

METAL SCREWS.

 7’     (2.13m)

  15’      (4.6m)

20’    (6.1m)

18”    (457mm)

Minimum width of floor protection from side of door opening(in U.S.A.) and 

from side of unit(in Canada).

Fireplace Clearances and Dimensions

  22”     (560mm)

  35’      (10.7m)

Recommended maximum chimney height (at sea level) from top of fireplace

to rain cap.

Minimum distance of adjacent wall to side of fireplace door.

Distance of combustible material from side, back standoffs and framing kit.

Ceiling clearance: from the base of the fireplace to the 

ceiling.

Minimum chimney height: minimum total chimney height from fireplace 

bottom to below the chimney rain cap.

Maximum unsupported chimney height.

Minimum depth of non-combustible ember protector: from the front of the

fireplace.

Minimum distance to side facing from fireplace door opening.

11 1/2”    (292mm)

16

5055.7618_210916-32

FP25.BODYA

Содержание FP25AR

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды