manualshive.com logo in svg

Pacific energy FP25AR, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pacific energy FP25AR Скачать руководство пользователя страница 15

Chimney 

Installation

Listed Chimney and Chimney Connector

This appliance must be installed with a 6"(150mm) chimney 
system  approved under the following standards: CAN-ULC S629(IN 
CANADA) OR UL 103hT(IN U.S.).

yOU MUST FOLLOW ThE ChIMNEy MANUFACTURER'S 
INSTALLATION INSTRUCTIONS FOR INSTALLATION OF 
ALL ChIMNEy COMPONENTS.

MAINTAIN CLEARANCES TO COMBUSTIBLES AS 
SPECIFIED IN ThE ChIMNEy MANUFACTURERS 
INSTALLATION INSTRUCTIONS

USE APPROPRIATE SUPPORTS, CAPS, FLAShING 
AND ShIELDS IN ACCORDANCE WITh ThE ChIMNEy 
MANUFACTURERS INSTALLATION INSTRUCTIONS.

ThE FOLLOWING INSTRUCTIONS ARE GENERAL 
GUIDELINES ONLy.

CAUTION: ThE STRUCTURAL INTEGRITy OF  ThE FLOOR, 
WALL AND CEILING/ROOF MUST BE MAINTAINED.

NOTE:  FOR  ALL  CHIMNEYS,  YOU  MUST  USE  THE 

MANUFACTURER'S  FIREPLACE  ANCHOR  PLATE. 

(If 

using ICC chimney pipe and anchor plate, you will need 
to install an Anchor Plate spacer. Part #FP30.7757)

NOTE: The FP25 must be installed so the outlet of the chimney 

system is a minimum 15ft(4.6m) in height as measured from 

the base of the unit up to a maximum height of 35'(10.7m). 

The chimney must be supported on lengths over 20'(6.1m).

NOTE:

 Longer chimney lengths and different pitch flashings 

may  be  used.    Install  all  components  to  the  chimney 

manufacturer's  installation  requirements.  Consult  your 

chimney supplier for installation advice.

1.  After  locating  the  desired  location  and  framing  in  the 

fireplace, cut and frame square holes in all floors, ceilings, 

and roof that the chimney will pass through. Use a plumb 

bob to line up the holes. The chimney support is mounted 

to the framing.

2.  Maintain a minimum 2"(51mm) clearance between the 

chimney and any combustible materials. Do not fill the 

space with insulation or any other combustible material.

3.  Install the pipe manufacturer's, 

fireplace anchor plate

 

by  inserting  it  into  the  flue  collar  on  the  fireplace.  We 

recommend sealing the joint with stove cement.  Secure 

the anchor plate with stainless steel screws.

4.  Assemble the chimney sections so the finished length 

is resting on the manufacturer's adapter and protruding 

through the roof. Avoid having joints between the ceiling 

and the roof. It is required that the chimney connections 

be secured with three (3)-#8x½"(12 mm) metal screws.

5.  Install  the  radiation  shields,  firestops  and  all  pieces 

necessary to prevent contact with combustible materials 

whenever passing through floors, ceilings or attic spaces.

6.  Install the roof support then assemble the flashing and 

the storm collar. Be sure to maintain the vapour barrier 

at this point. (Seal securely.) 

7.  Attach the rain cap and check the flashing for leaks.

8.  If  the  chimney  extends  more  than  5'(1.5m)  above  the 

point of contact with the roof, then it must be secured 

using roof braces.

Chase/Enclosure

WARNING: Combustible materials cannot be used in the 

space directly above the fireplace. Do not fill the space 

above the fireplace with any material. (except the wood 

framing)

WARNING: The fireplace must not be in contact with any 

insulation  or  loose  filling  material.  Cover  the  insulation 

with  drywall  panels  around  the  fireplace.  Maintain  proper 

clearances as per Fig. #7.

WARNING: Drywall materials are considered combustible 

and theIr thickness must be accounted for in your framing 

dimensions.

If  the  chimney  runs  up  the  outside  of  the  residence,  we 

recommend it be enclosed in a chase structure. The chase 

should be constructed in such a way that it is an extension of 

the home. It should be well insulated between the footings and 

the floor of the home to prevent heat loss.  We also recommend 

to insulate the ceiling of the chase just as if it were in the attic 

space. This will prevent cold air from dropping down through 

the chase and into the room where the fireplace is installed. 

Some local codes require that the walls be insulated, vapor 

sealed and sheathed with a fire rated gypsum board. We 

strongly  recommend  this  procedure  for  all  installations  to 

prevent cold drafts from originating in the fireplace enclosure. 

If you follow this procedure, do not insulate the wall directly 

above the front of the fireplace.

NOTE: Check local codes concerning installation requirements 

and restrictions in your area.

Mobile home Installation:

-  In the USA: the unit must be installed in accoradance with 

the requirements of the Department of Housing and Urban 

Development(HUD)"Manufactured  Home  Construction 

and Safety)

-  In Canada: the unit must be installed with access openings 

into the built in enclosure for inspection purposes that 

must require a household tool to open.

15

5055.7618_210916-32

FP25.BODYA

Содержание FP25AR

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды