4
1. Be certain equipment (boom, sheave blocks, pen-
dants, etc.) is either lowered to the ground or
blocked securely before servicing, adjusting, or
repairing hoist.
2. Be sure personnel are clear of work area BEFORE
operating hoist.
3. Read all warning and caution tags provided for safe
operation and service of the hoist and become
familiar with the operation and function of all con-
trols before operating the hoist.
4. Inspect rigging and hoist at the beginning of each
work shift. Defects should be corrected immediate-
ly. Do not operate a hoist with defects.
5. Keep equipment in good operating condition.
Perform scheduled servicing and adjustments listed
in the “Preventive Maintenance” section of this
manual.
6. An equipment warm-up procedure is recommended
for all start-ups and essential at ambient tempera-
tures below +40°F (+4°C). Refer to “Warm-up
Procedure” listed in the “Preventive Maintenance”
section of this manual.
7. Do not exceed the maximum pressure (PSI, kPa) or
flow (GPM, lpm) stated in the hoist specifications
found in the specific sales brochure.
8. Operate hoist line speeds to match job conditions.
9. Protective gloves should be used when handling
wire rope.
10. Never attempt to handle wire rope when the hook
end is not free. Keep all parts of body and clothing
clear of cable rollers, cable entry area of fairleads,
sheaves and hoist drum.
11. When winding wire rope on the hoist drum, never
attempt to maintain tension by allowing wire rope to
slip through hands. Always use “Hand-Over-Hand”
technique.
12. Never use wire rope with broken strands. Replace
wire rope that is damaged. Refer to wire rope sup-
plier manual.
13. Do not weld on any part of the hoist without
approval from PACCAR Winch Engineering.
14. Use recommended hydraulic oil and gear lubricant.
15. Keep hydraulic system clean and free from contam-
ination at all times.
16. Use correct anchor for wire rope and pocket in
drum.
17. Do not use knots to secure or attach wire rope.
18. The BRADEN designed wire rope anchors are not
intended to support the rated load. ALWAYS main-
tain a minimum of five (5) wraps of wire rope on the
drum. It is recommended that the last five (5) wraps
of wire rope be painted bright red to serve as a visu-
al reminder.
19. Never attempt to clean, oil or perform any mainte-
nance on a machine with the engine or prime mover
running, unless instructed to do so in this manual.
20. Never operate hoist controls unless you are proper-
ly positioned at the operators station and you are
sure personnel are clear of the work area.
21. Assure that personnel who are responsible for hand
signals are clearly visible and that the signals to be
used are thoroughly understood by everyone.
22. Ground personnel should stay in view of the opera-
tor and clear of the hoist drum. Do not allow ground
personnel near wire rope under tension. A safe dis-
tance of 1
½
times the working length of the wire
rope should be maintained.
23. Install guarding to prevent personnel from getting
any part of body or clothing caught at a point where
the cable is wrapped onto the drum or drawn
through guide rollers or potential “pinch points”.
24. Install switches or valves that will shut off power to
the hoist, in locations where they can be reached by
anyone entangled in the wire rope before being
drawn into the hoist or any “pinch point”.
25. “Deadman” controls, which automatically shut off
power to the hoist whenever the operator leaves his
station or releases the hoist control lever, should be
installed whenever practical.
26. Never allow anyone to position any part of body
under a suspended load.
27. Avoid sudden “shock” loads or attempting to “jerk” a
load free. This type of operation may cause heavy
loads, in excess of rated capacity, which may result
in failure of wire rope, hoist or crane structure.
28. Whenever possible, install the hoist in a location
that is not immediately adjacent to a “normal” oper-
ator’s station.
29. All hoist controls shall be located within easy reach
of the operator. The controls shall be installed in
such a location that the operator is removed from
the electrical path to ground if the load, rigging, or
wire rope come in contact with or within proximity to
an electrically energized conductor.
GENERAL SAFETY RECOMMENDATIONS
Safety for operators and ground personnel is of prime concern. Always take the necessary precautions to ensure
safety to others as well as yourself. To ensure safety, the prime mover and hoist must be operated with care and
concern for the equipment and a thorough knowledge of the machine’s performance capabilities. The following
recommendations are offered as a general safety guide. Local rules and regulations will also apply.
