background image

1.2.4 DO NOT use in an enclosed area or a 
moving vehicle. 
1.3. 

General fuel safety. 

ALL FUELS ARE FLAMMABLE 
1.3.1.  Fire hazard - keep fuel away from all 

sources of ignition for example heaters, lamps, 
sparks from grinding or welding. 

1.3.2.  DO NOT carry out hot work on tanks 

that have contained fuel it is extremely 
dangerous. 
1.3.3.  ALWAYS keep work area clean and 
tidy. 
1.3.4.  ALWAYS clean up all spills promptly 

using correct methods i.e. absorbent granules 
and a lidded bin. 
1.3.5.  ALWAYS dispose of waste fuels 
correctly. 
1.4. 

Fueling/De-fueling. 

 ALL FUELS ARE FLAMMABLE 
1.4.1.  ALWAYS fuel and defuel in a well-
ventilated area outside of buildings. 
1.4.2.  ALWAYS wear correct, suitable and fit 

for purpose Personal Protective Equipment 

(PPE), suggested items are but not limited to 
safety gloves and overalls. 

1.4.3.  When fueling/de-fueling ALWAYS 
avoid inhaling fumes 
1.4.4.  When de-fueling ALWAYS use a 
propriety fuel retriever. 
1.4.5.  ALWAYS carry fuel in the correct and 
clearly marked container. 

1.5. 

Electrical safety. 

1.5.1.  Electricity can kill - NEVER use 

pressure washer jet to come into contact with 

LIVE or ENERGISED equipment. It can also 
cause severe burns. 
1.5.2.  NEVER work on or near electricity with 
wet hands, wet clothing, and wet gloves. 
1.6. 

Vibrations. 

1.6.1.  Prolonged use of hand held (operated) 

machines will cause the user to feel the effects 

of/from vibrations. These vibrations can lead 

to white finger (Raynaud's phenomenon) or 

carpal tunnel syndrome. This condition 

reduces the ability of the hand to feel and 

regulate temperature, causing numbness and 

heat sensations and may cause nerve damage 
and circulatory tissue death. 
1.6.2.  Not all factors that lead to white finger 

disease are known, but cold weather, smoking 

and other diseases that affect blood vessels 

and blood circulation as well as large and long-

lasting impact of shocks are considered factors 

in the formation of white finger. Note the 

following to reduce the risk the white finger 

and carpal tunnel syndrome: 
1.6.2.1. Wear gloves and keep your hands 
warm 
1.6.2.2. Take regular breaks 
1.6.3.  All of the above precautions may help 

reduce the risk of white finger disease but not 

rule out carpal tunnel syndrome. Long-term 

and regular users are therefore recommended 

to observe the condition of your hands and 

fingers. Seek medical attention immediately if 

any of the above symptoms should occur. 
1.8. 

Noise. 

1.8.1.  The operating noise of the machine 

can damage your hearing. Wear hearing 

protection such as earplugs or ear defenders 

to protect your hearing. Long- term and 

regular users are advised to have hearing 

checked regularly. Be especially vigilant and 

cautious when wearing hearing protection 

because your ability to hear alarm warnings 
will be reduced. 
1.8.2.  Noise emissions for this equipment is 

unavoidable. Carry out noisy work at approved 

times and for certain periods. Limit the 

working time to a minimum. For your personal 

protection and protection of people working 

nearby it is also advisable for them to wear 
hearing protection. 

Page 5

First edition - 

April

 201

7

Содержание P72800A

































Отзывы: