background image

35

Device settings -> Relay control

Relay control           

Pump summer stop: 

Relay control according to the temperature:

Give the controller an outdoor temperature limit at which it stops. 

The controller is given an outdoor temperature limit at which the 

controller is stopped. You can select here or in H2 control circuit spe-

cial settings either to close the H2 valve or keep it on control when the 

pump stops (see p. 47). Connect the pump to the extension unit’s row 

connectors 21 and 23. The 230 V power source that the pump requires 

can be taken through the external source ( see separate instructions).

   Device settings > Relay control

   > Laiteasetukset... Pumpun kesäpysäytys

Relay control                                    Pump summer stop           

Summer function  (outdoor temp. limit)               19°C >
Valve position at summer function            In control > 

 

   Device settings > Relay control

Not in use

Pump summer stop                        

                         

According to the temperature 

                                   >

Accord. to temp.  difference

                           

Accord. to H1 valve

 

position

                 

Accord. to the time program
General alarm

                             

Relay control can be taken into use if an extension unit has been con-

nected to the controller using an RJ45-2 channel. Select the relay use.

  Summer function  (outdoor temp. limit)

19°C

min: 5  max: 95.0

 

Valve position at summer function 

In control

Closed

 

Setting  at  which  the relay  is  active

55 °C

min: 0  max: 95

     Device settings > Relay control

   

Relay control            According to the temperature >     

Meas. that controls the relay                 Boiler temp.  >
Setting  at  which  the relay  is  active              58

°C >

Hysteresis                                                                     5

°C >

Relay is active:      When meas. drops below setting >

  

Meas. that controls the relay   

Measurement  1   Outdoor temperature

ittaus 2                                                     

Measurement 2   H1  Supply water    
Measurement 3   H1 Room measurem. TMR 
Measurement 4   Solar collector
Measurement 5   Boiler temp.
Measurement 6   Not in use 

   Relay is active:

When meas. drops below setting

 When meas.goes above setting

Select which temperature controls the relay.  If the measurement 

channel has not been taken into use or you want to use it for somet-

hing else, make the change at “Measurement channel settings” in 

device settings. 

”When meas. drops below setting”:

 Relay control switches on when 

the temperature drops to the set value and switches off when the tem-

perature rises the amount of the hysteresis above the set value. Use 

this, e.g., when controlling an additional source of heat on (e.g., elec-

tric heater) or in an automobile heater outlet. 

”When meas. goes above setting”:

  Relay control switches on when 

the temperature rises to the set value and switches off when the 

temperature drops the amount of the hysteresis below the set value. 

This can, e.g., control a cold room’s compressor or heat distribution 

room’s fan. 

  Hysteresis

3 °C

min: 1  max: 10

Содержание EH-800





























































Отзывы: