Measurements
H1
Supply=52/
H1
Room=21.2/
H1
Ret.water=28/
Outdoor=-15/
H2
Supply=48/
Exhaust=25/
OUMAN EH-201/L
MODEM SETTING
(TEXT MESSAGE CONNECTION)
OUMAN EH-201/L
TextMessageSett.
Alarm GSM1 nr
Alarm GSM2 nr
Device ID
MessageCentreNr
PIN-code
Modem type
Modem connect
Data link
Text message
The regulator's strip connector B-D space is connected with a jumper
wire.
Press the
button to move the cursor to
. Press
"Text message”
OK
.
Telephone nr.
Change
PIN-code
Change
----
Modem type
Falcom A2D
Siemens M20T
Ouman/Fargo
Press the
button to move the cursor to "Change”.
Press
. "O” blinks.
Write the telephone number using the text editor.
You can move forward or backward in the character
OK
Give a telephone number that the regulator automatically sends a text
message to about an alarm in the event of an alarm. At first the
alarm message is only sent to the GSM number 1. If the alarm is
not acknowledged from this number, after five minutes the regulator
sends a new alarm to both the GSM 1 and 2 numbers.
The regulator can be given a device ID, which functions as the device's
secret password and address information. The device ID can be freely
labeled. The device ID is always written in front of the keyword when
using the GSM to communicate with the regulator.
Telephone nr.
Change
Device ID
Not in use
In use
0000
GSM-modem
GSM network
Connecting the GSM modem's D-9 con nector to the EH-201/L regulator:
gree
n
brown
yello
w
Ouman
EH-201/L
regulator
A
B
C
D
jumper wire
Installing receivers for alarm messages:
Device ID:
In order to communicate via text messages, the regulator must be connected to a
GSM modem (optional equipment). The modem comes with an adapter cable
equipped with a D-connector that is used to connect modem to the regulator. The
regulator's strip connector B-D space is connected with a jumper wire. GSM
modem connection is done in start functions. The regulator automatically
initializes the GSM mode in two hour intervals. This prevents the GSM from
becoming disconnected in the event of power failures.
Directions for entering the
maintenance mode are on page 21.
Special mainten.
Rstore settings
Settings
Meas. 3 setting
Dig1 selection
Dig2 selection
LON initializ.
Net measurement
Text message
row with the
or button. Confirm the number by pressing
, then
the same number that you selected will blink in the next space.
Whichever has been selected last can be deleted by pressing
. If
you press the
button for a while, the number will be deleted and
the number that was previously fed will remain in effect. When you
are ready, press
for a while (over 2 secretary.).
-
+
OK
ESC
ESC
OK
Move the cursor to "In use”. Press
. "0" blinks.
Write a device ID that has a max. of 4 characters.
The text editor has the letters A…Z and the
numbers 0…9. You can move forward or backward
in the character row by pressing the
or
button.
Confirm the character by pressing
.
Give the operator-specific message center number
with
or
button. Confirm by pressing
.
Give the SIM card's PIN code. The regulator will
not initialize the GSM modem before the PIN code
is installed. The SIM card has to be put in the
GSM telephone to change the modem's PIN
code. When you have changed the PIN code,
install the SIM card back in the modem.
EH-201/L is compatible with Falcom A2D and
Siemens M20T modems.
OK
OK
OK
+
-
Installing the number for the message center:
+
-
Installing the modem's PIN for the regulator:
Selecting the modem type:
ESC - press to return to the previous display
Info button - gives operating instructions
Browse button - moves the cursor up and down
ESC
Group select button - not in use in EH201/L
37
GSM-modem
