OTT Pluvio 2 S Скачать руководство пользователя страница 40

Страница: 40 / 56

Orifice rim heater self-test failed/is not run

䊳

Orifice rim heater supply voltage is missing, incorrectly connected, or is outside

the specified range:

➝

restore power supply to the orifice rim heater (replace fuse as necessary);

➝

check supply voltage level and adjust as necessary;

➝

check wiring of the orifice rim heater and correct as necessary.

䊳

Pipe housing (including built-in orifice rim heater) is not installed:

➝

install the pipe housing.

䊳

Pipe housing without built-in orifice rim heater of another OTT Pluvio

S is

accidentally installed:

➝

install the pipe housing with built-in orifice rim heater.

䊳

No self-test is run:

➝

check the “Self-test interval” (Modes 2, 3, 4) setting and correct as

necessary (using the OTT Pluvio² Operating Software);

➝

force self-test by a “Power-Reset” once.

Orifice rim heater does not work/does not work as expected

䊳

Orifice rim heater supply voltage is missing, incorrectly connected, or is outside

the specified range:

➝

restore power supply to the orifice rim heater (replace fuse as necessary);

➝

check supply voltage level and adjust as necessary; make sure that output

power of power source is sufficient;

➝

check orifice rim heater wiring and correct as necessary; make sure that

cable cross-section is sufficient;

➝

check heater status (using the OTT Pluvio² Operating Software).

䊳

Pipe housing (including built-in orifice rim heater) is not installed:

➝

install the pipe housing.

䊳

Pipe housing without built-in orifice rim heater of another OTT Pluvio² S is

accidentally installed:

➝

install the pipe housing with built-in orifice rim heater.

䊳

Configuration of the orifice rim heater results in unexpected heater

performance:

➝

check settings

– mode of operation

– orifice rim target temperature (modes #1, #2, #3, #4)

– lower temperature limit (mode #2)

– switch-on time (mode #3)

– on-time (mode #3)

– after-run time (mode #4)

and correct as necessary (using the OTT Pluvio² Operating Software).

䊳

OTT Pluvio² S system time is incorrect (e.g. after power supply failure):

➝

correct system time (using the OTT Pluvio² Operating Software).

Содержание Pluvio 2 S

























































Результаты поиска

Содержание Pluvio 2 S

Отзывы:

Похожие инструкции для Pluvio 2 S

Бренды по названию

Популярные бренды

OTT Pluvio 2 S, Руководство по эксплуатации

Результаты поиска

Содержание Pluvio 2 S

Отзывы:

Похожие инструкции для Pluvio 2 S

Бренды по названию

Популярные бренды