Oshkosh Corporation JLG R2632 Скачать руководство пользователя страница 70

Страница: 70 / 108

SECTION 5 - ACCESSORIES

5-8

31215932

5.7

FOOTSWITCH

The Footswitch serves as another enable switch in the function con

trol circuit. It must be depressed in sequence with the platform con

trol joystick trigger switch to enable operation of machine fucntions

when using the platform controls. Power is removed from the plat

form controls when the footswitch is released.

NOTE:

This accessory is only available in Japanese and Korean markets.

Operation

To operate a function, engage the footswitch and joystick trigger in

any sequence.

5.8

MAGNETIC GATE LATCH

The Magnetic Gate Latch ensures the platform gate latches securely

when closed.

Grasp handle and pull out to unlatch. Swing open the gate.

Footswitch Assembly

OAD00120

Magnetic Gate Latch Assembly

Содержание JLG R2632













































































































Результаты поиска

Содержание JLG R2632

Отзывы:

Похожие инструкции для JLG R2632

Бренды по названию

Популярные бренды

Oshkosh Corporation JLG R2632, Руководство по эксплуатации и безопасности

Результаты поиска

Содержание JLG R2632

Отзывы:

Похожие инструкции для JLG R2632

Бренды по названию

Популярные бренды