Oshkosh Corporation JLG R2632 Скачать руководство пользователя

Страница: 55 / 108

SECTION 3 - MACHINE CONTROLS, INDICATORS, AND OPERATION

31215932

3-23

3.14 MACHINE LIFTING AND TIE DOWN

The machine may be lifted using a forklift truck. Lift only using the

built-in forklift pockets at the rear of the machine and only with the

platform in the stowed position. First adjust the width of the forklift

truck lifting tines to fit the machine forklift pockets.

Then slide the

tines into the forklift pockets and carefully lift machine.

The machine may also be lifted using a spreader bar and four equal

length straps or chains capable of supporting the full gross weight of

the machine. Lift only using the lifting lugs provided at the four cor

ners of the machine.

0"%

Содержание JLG R2632













































































































Результаты поиска

Содержание JLG R2632

Отзывы:

Похожие инструкции для JLG R2632

Бренды по названию

Популярные бренды

Oshkosh Corporation JLG R2632, Руководство по эксплуатации и безопасности

Результаты поиска

Содержание JLG R2632

Отзывы:

Похожие инструкции для JLG R2632

Бренды по названию

Популярные бренды