Orientalmotor CSK243-ATA Скачать руководство пользователя страница 13

Страница: 13 / 48

4 Preparation

−

No. Name

Description

Potentiometer for adjusting the
motor standstill current
(STOP VR)

This potentiometer sets the current when the
motor is at a standstill (in the current cutback
state).
Factory setting: 40% of the rated current

Positive check terminal for
motor operating current (C.C.+)

This terminal is used to check the motor
operating current.

Negative check terminal for
motor operating current (C.C.

−

)

This terminal is used to check the motor
operating current.

CSD2140T

CSD2145T

Heat sink

Mounting holes

Mounting
holes

No. Name

Description

Power supply terminal blocks
(TB1)

Connected to 24 VDC power supply.

Motor terminal blocks (TB2)

Connected to motor leads.

I/O terminal blocks (TB3)

Connected to I/O signals.

Potentiometer for adjusting the
motor operating current
(RUN VR)

This potentiometer sets the operating current
of the motor. If there is sufficient torque, the
current setting can be reduced to suppress
increases in motor/driver temperatures.
Factory setting: the rated current

Potentiometer for adjusting the
motor standstill current
(STOP VR)

This potentiometer sets the current when the
motor is at a standstill (in the current cutback
state).
Factory setting: 40% of the rated current

Automatic current cutback
function jumper socket
(C.C./A.C.D.)

This switch enables or disables the automatic
current cutback function.
Factory setting: [A.C.D.] (enable)

Содержание CSK243-ATA

















































Результаты поиска

Содержание CSK243-ATA

Отзывы:

Похожие инструкции для CSK243-ATA

Бренды по названию

Популярные бренды

Orientalmotor CSK243-ATA, Руководство по эксплуатации

Результаты поиска

Содержание CSK243-ATA

Отзывы:

Похожие инструкции для CSK243-ATA

Бренды по названию

Популярные бренды