Orientalmotor CSK243-ATA Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 48

background image

5 Installation

−

19

−

5.5 Installing the driver

When installing the driver in an enclosure, be sure to follow the diagram illustrated.
Provide a minimum clearance of 25 mm (1 in.) in the horizontal direction or 50 mm
(2 in.) in the vertical direction between the driver and enclosure or other equipment
within the enclosure. When installing two or more drivers side by side, provide a
minimum clearance of 20 mm (0.79 in.) between drivers.

Note

•

Do not install any equipment that generates a large amount of heat near
the driver.

•

Check ventilation if the ambient temperature of the driver exceeds 40 °C
(104 °F).

CSD2109-T

,

CSD2112-T

,

CSD2120-T

Mount the printed circuit board or heat sink to the mounting plate. (Screws and
spacers are not supplied.)

•

Mounting the heat sink

Mount the heat sink to the mounting
plate using M3 screws.

M3

Spring washer

Mounting plate

M3
Effective depth:
5 mm (0.2 in.)

M3 screws

•

Mounting the printed circuit board

Mount the printed circuit board to the mounting plate using No.4-40 UNC screws.
Insert a spacer [5 mm (0.2 in.) or thicker] between the printed circuit board and the
mounting plate.

•

Horizontal installation

Spacer
(insulation material)

Mounting
plate

No.4-40 UNC
screw

•

Vertical installation

Install the driver so

that the connector

is positioned on

the bottom side.

Mounting

plate

No.4-40 UNC screw

Spacer
(insulation material)

«
...
17
18
19
20
21
...
»

Содержание CSK243-ATA

















































Отзывы:

Нет отзывов

Похожие инструкции для CSK243-ATA

Plug & Play Plus

Бренд: CHERUBINI Страницы: 16

Бренд: Rato Страницы: 32

Бренд: Hatz Diesel Страницы: 56

Бренд: Continental Motors Страницы: 146

Бренд: Leb Electronics Страницы: 24

Бренд: Westerbeke Страницы: 140

Бренд: Briggs & Stratton Страницы: 26

Бренд: Danfoss Страницы: 77

Бренд: Superior Страницы: 114

Бренд: O.S. engine Страницы: 4

Бренд: DLE Страницы: 4

Бренд: JetCat Страницы: 54

Бренд: Vetus Страницы: 28

iSV2-CAN Series

Бренд: Leadshine Страницы: 107

Nanomotion SE Series

Бренд: Johnson Electric Страницы: 33

Бренд: PRETUL Страницы: 32

Бренд: O.S. engine Страницы: 21

Бренд: sati Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды