Orbis CALORAMA Скачать руководство пользователя страница 5

4

SAFETY INFORMATION FOR USERS OF PROPANE / L.P. GAS:

Propane/L.P. gas is highly flammable gas that can cause fire and explosions. Propane/L.P. 
gas is naturally odorless, but a special odorant is added to the gas to alert you to the 
presence of a gas leak, should one occur. This odor may fade over time. It is recommended 
that you obtain a "Scratch and Sniff" brochure to familiarize occupants with the odor 
associated with propane/LP gas. Not everyone is familiar with the safety precautions 
covering the use of Propane/L.P. gas. These precautions will help you safeguard your 
family and your property from an accident. Read the following carefully and make sure 
that everyone in your household knows the correct action to take in the event of a leak 
in the Propane/L.P. gas system.

PROPANE / L.P. GAS ODOR WARNING 

The odorant put into the Propane/L.P. gas by your gas supplier will allow you to detect 
the distinctive smell of gas in the event of a leak. If you smell propane / L.P gas anywhere 
in or around your house or apartment, this odor indicates it is time to take immediate 
action in order to reduce or eliminate the risk of injury and or property damage.  

KNOW AND MAKE SURE OTHERS IN YOUR HOUSEHOLD KNOW THE FOLLOWING 
PROCEDURES TO TAKE IN THE EVENT OF A PROPANE / L.P. GAS LEAK:

1. DO NOT operate electric switches, light matches, or use your telephone.  Do not do 
anything that could create an open flame or sparks, resulting in the ignition of leaking gas.

2. USE a neighbor’s telephone and call a qualified Propane / L.P. gas service technician 
or the gas supplier AND the fire department.  Even if the odor of Propane / L.P. gas fades
 and you cannot detect the smell of gas, DO NOT turn on any appliances.  

3. DO NOT re-enter the building or area until it has been declared safe to enter by the 
fire department or other authority. A properly trained and qualified Propane / L.P. gas 
service technician or gas supplier must repair the system leak and then re-light your gas 
appliances for you.

WARNING:  DO NOT USE THIS HEATER IF ANY PART HAS BEEN UNDER WATER.  

IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE APPLIANCE 

AND TO REPLACE ANY PART OF THE CONTROL SYSTEM 

AND ANY GAS CONTROL WHICH HAS BEEN UNDER WATER.

IF YOU DO NOT UNDERSTAND THIS INFORMATION OR FEEL YOU NEED 

ADDITIONAL INFORMATION, CONTACT YOUR GAS SUPPLIER.

Содержание CALORAMA































Отзывы: