16
Installing the Unit Cover:
Slide the heads of the two (2) bolts at the bottom of the front cover into the
corresponding holes in the back cover (with the upper end of the front cover leaning
about an inch forward), push the front cover in and down until the bolts lock into place.
Slide the overhangs at the upper end of the front cover under the back cover and fix with
the two (2) screws.
Secure the two (2) bolts at the bottom of the front cover.
Lighting the Unit:
The pilot and main burner lighting instructions for this unit can be found as a full size
label which is attached to a plate of sheet metal which hangs on a chain at the rear of
the heating unit. The instructions can also be found at Figure 10 below. These instructions
will direct you through the complete safe lighting and operation of the gas control system.
Figure 10: lighting Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing propety damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas.
Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electric switch; do not use any phone in your building.
* Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier´s instructions.
* If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don´t try to repair it; call qualified service technician.
Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any
gas control which has been under water.
LIGHTING INSTRUCTIONS
TO TURN OFF GAS TO APPLIANCE
1. STOP: Read the safety information above on this label.
Tum gas control clockwise to the “OFF” podition. Do noy force.
2. Turn gas control knob clockwise to “OFF”.
3. Wait five (5) minutes to clear
out any gas. Then smell for gas,
including near the floor. If you
smell gas, STOP! Follow “B” in the
safety information above on this label.
If you don´t smell gas, go to the next step.
4. Find pilot by looking through
the upper Heat exchanger window
of the heather.
5. Turn gas control knob counterclokwise to “PILOT”.
6. Push in the control knob all the way and hold in 90 seconds. Then
light the pilot with the piezoelectric igniter (black knob)
several times if necessary, until it is lit. Continue to hold
the control knob in for about one (1) minute after the pilot is lit.
Release the knob and irt will pop back up. Pilot should remain lit;
if it goes out, repeat steps 1 through 6.
* If the knob does not pop up when released, stop and immediately
call your service technician or gas supplier.
* If the pilot will not stay lit after several tries, turn the gas control
knob to “OFF” and call your service technician or gas supplier.
7. Repleace the front panel (if removed)
8. Turn gas control knob counterclockwise to the
desired temperature setting.
⅝
⅔
½¾
⅝⅔
“LO”
-
IGNITER
BUTTON
GAS CONTROL
KNOB
SHOWN IN
“OFF” POSITION
“HI”+
THERMOCOUPLE
PILOT
PILOT
ELECTRODE
CERAMIC
DUE TO HIGH SURFACE TEMPERATURES, KEEP CHILDREN, CLOTHING, AND FURNITURE AWAY.
KEEP BURNER AND CONTROL COMPARTMENT CLEAN.
SEE INSTALLATION AND OPERATING INSTRUCTIONS ACCOMPANYNG APPLIANCE.