manualshive.com logo in svg

Oracle Tekelec 1200, Руководство по установке

Поделиться
Скачать
Oracle Tekelec 1200 Скачать руководство пользователя страница 64

Power Requirements in a DC Environment

A Direct Current (DC) environment must supply 14 60-Amp feeds from the customer’s power source.
Each cabinet is divided into A and B power buses, each with seven feeds. If loss of power on one of
the buses occurs, the other bus must be able to supply current for the entire cabinet.

Note:  The nominal voltage is -48VDC, and operating voltage range is -40VDC to -56.7VDC.

Note:  The DC return terminal is not connected to the equipment frame or the grounding means of
the equipment, Isolated DC return (DC-I).

Note:  If breakers are tripped, they must be switched completely OFF and then ON to reset.

Note:  The size of the cable is determined by the overall length of the cable run. Refer to the Site File
Book.

Procedure — Power Terminations

All power terminations on the 3U PDP will be #6 awg. Use H-taps for each -48vdc and RTN run to
reduce the wire size to the proper gauge required.

Table 4-1 shows the list of required wiring sizes based on the length of the cable run. All cable equipment
power ratings are 125A @ -48VDC.

Table 4: Table 4-1. Power Cable Conductor Sizes

Conductor Size (AWG)

Cable Length

Breaker Size in
Amperes

#6

up to 40 ft. (12.2 meters)

40A

#4

up to 70 ft. (21.3 meters)

#2

up to 110 ft. (33.5 meters)

1/0

up to 170 ft. (51.8 meters)

2/0

up to 200 ft. (61 meters)

4/0

up to 220 ft. (67.1 meters)

#2

up to 40 ft. (12.2 meters)

60A

1/0

up to 70 ft. (21.3 meters)

2/0

up to 110 ft. (33.5 meters)

4/0

up to 170 ft. (51.8 meters)

350MCM

up to 200 ft. (61 meters)

350MCM

up to 220 ft. (67.1 meters)

64

910-5681-001 Revision E, February 2014

Cabinet Installation

Installation

Содержание Tekelec 1200













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды