Oracle SG-SAS6-INT-Z Скачать руководство пользователя страница 25

Страница: 25 / 80

♦ ♦ ♦ C H A P T E R 3

Creating a Bootable Drive in a Preboot

Environment

This chapter describes how to use the HBA for your boot device prior to installing an operating

system (OS) on the system.

Note -

If you are installing the HBA into a system that already has an OS installed, do not

perform any procedures in this chapter. Instead, complete the HBA installation, as described in

“To Complete the Installation” on page 20

This chapter contains the following topics:

■

“Overview of Creating a Bootable Drive in a Preboot Environment” on page 25

■

“Creating a Bootable Drive (SPARC)” on page 27

■

“Creating a Bootable Drive (x86)” on page 32

■

“Validating the Label of the HBA Drive” on page 49

■

“Installing the Oracle Solaris OS” on page 51

■

“Next Steps” on page 52

Overview of Creating a Bootable Drive in a Preboot

Environment

As an installation option, you can choose to install the HBA into a system that does not yet

have an OS installed. With this installation option, if you plan to use the HBA as your boot

device, you can optionally create a RAID volume for the HBA. You can then install the OS onto

a physical drive or onto that RAID volume to enable you to boot from the HBA. On a SPARC

system, you would perform these actions through the

FCode

utility. On an x86 system, you

would do so either through the Unified Extensible Firmware Interface (UEFI) Drive Control

menu of the BIOS Setup utility (UEFI booting) or through the BIOS Configuration utility

(Legacy BIOS booting).

Chapter 3 • Creating a Bootable Drive in a Preboot Environment

Содержание SG-SAS6-INT-Z

















































































Результаты поиска

Содержание SG-SAS6-INT-Z

Отзывы:

Похожие инструкции для SG-SAS6-INT-Z

Бренды по названию

Популярные бренды

Oracle SG-SAS6-INT-Z, Руководство по установке

Результаты поиска

Содержание SG-SAS6-INT-Z

Отзывы:

Похожие инструкции для SG-SAS6-INT-Z

Бренды по названию

Популярные бренды