Optics OMM-1000 страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 49

background image

20

4.1 Basic setup

Click

Set Config

button to set the communication method, input / output name, Video generator and

so on. Then, the Set Config window as below will open.

Fig 4-2 Set Config window of OMM-1000 PC program

4.1.1 Connect Info

▪

Select the way of control method between RS-232 and Ethernet (UDP) by click the radio
buttons.

▪

In case of RS-232 control, enter available COM port number of your PC and select baud
rate. The baud rate should be same as that OMM-1000. (115200 is default)

▪

In case of Ethernet, enter IP address of OMM-1000 and port number. 3000 is default port
number of OMM-1000.

▪

Click save button and close Set Config window then click

Connect

button on PC program

of OMM-1000 to start it.

▪

If the connection is properly made, current status of OMM-1000 will be shown at the

«
...
18
19
20
21
22
...
»

Содержание OMM-1000


















































Отзывы:

Нет отзывов

Похожие инструкции для OMM-1000

Бренд: Jet City Страницы: 6

trans-nova 9505

Бренд: Hafler Страницы: 24

Бренд: Hafler Страницы: 9

Бренд: Hafler Страницы: 7

Бренд: Hafler Страницы: 21

Бренд: Hafler Страницы: 2

Бренд: Baldwin Boxall Страницы: 4

Бренд: Korg Страницы: 31

Бренд: Luxman Страницы: 16

Бренд: UNI-T Страницы: 13

Бренд: SAL Страницы: 25

Бренд: Art Страницы: 25

Okur A7 Series A71100.1

Бренд: DB Drive Страницы: 12

Бренд: Technics Страницы: 10

Бренд: Advance acoustic Страницы: 20

Бренд: AMC Страницы: 6

Бренд: Rompa Страницы: 4

Бренд: NAIM Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды