Optics OMM-1000 Скачать руководство пользователя страница 5

Страница: 5 / 49

▪

Works with OPTICIS DVI, HDMI, SDI, and DisplayPort optical extender for long signal

extension.

▪

Has dual-power supplier for hot-swappable and load-sharing.

▪

Equips multi-viewer card to be used in various monitoring systems.

▪

Provides Preset mode to save and load the routings status.

▪

Provides diagnostic function for quick trouble shooting.

▪

Has video generator output and monitoring output for easy installation.

1.2 Shipping group

▪

OMM-1000, Modular matrix chassis: 1 EA

▪

Input output cards: Option



SDVI-4EI, 4 ports electrical Single link DVI input card



SDVI-4EO, 4 ports electrical Single link DVI output card



DDVI-2EI, 2 ports electrical Dual link DVI input card



DDVI-2EO, 2 ports electrical Dual link DVI output card



SDVI-1FI, 4 ports 1 fiber optical DVI input card



SDVI-1FO, 4 ports 1 fiber optical DVI output card



HDMI-4EI, 4 ports electrical HDMI input card



HDMI-4EI, 4 ports electrical HDMI output card



SDI-4EI, 4 ports electrical SDI input card



SDI-4EO, 4 ports electrical SDI output card



DP1-4EI, 4 ports electrical DisplayPort input card



DP1-4EO, 4 ports electrical DisplayPort output card



QDVI-O, Multi-viewer card

▪

AC power cord: 1 EA

▪

Power supplier: 1 EA (Dual power supplier is an option)

▪

User manual: 1 EA

▪

Firmware download cable: 1 EA (Use only this accessory specified by the manufacturer)

▪

RS-232 cable (Straight type): 1 EA

▪

PC software CD: 1 EA

1.3 Notice of safe usage

We recommend you to read following warning, precaution and information before start to
operate the OMM-1000 modular matrix.

▪

Use of the equipment in a manner not specified by the manufacturer may result in ire-

coverable damage.

Содержание OMM-1000


















































Результаты поиска

Содержание OMM-1000

Отзывы:

Optics OMM-1000, Руководство пользователя, Страница: 5 / 49

Результаты поиска

Содержание OMM-1000

Отзывы: