Optex TS-1000-D Скачать руководство пользователя страница 30

Страница: 30 / 36

Cleaning

Cleaning

Set the sensor cleaning setting from SC-U1.

To perform cleaning, press

Manual cleaning

Activate the wiper manually. While cleaning the measurement value of the
target sensor is retained (held).

Cleaning interval

Set a time interval to activate the wiper.
This product is a sensor with wipers and it operates as following.

・

The setting time for the cleaning interval is the time interval between the
end of cleaning and the next cleaning.

・

The cleaning action is fixed at 1 wiper blade round trip per cycle.

Item

Setting range

Factory default

setting

Cleaning Interval OFF (No cleaning)

10 to 1440 minutes (by 10 minutes)

30 minutes

For operation, refer to the "Universal Transmitter SC-U1 Operation
Manual", "9 Cleaning" and "

◆

Manual Cleaning".

Select an item from the following.

For operation, refer to the "Universal Transmitter SC-U1 Operation
Manual", "9 Cleaning" and "

◆

Cleaning Interval".

Caution

・

Pressing

automatically retains the measurement value.

・

Do not press

while a sensor with a wiper is in the air.

This may cause the sensor to malfunction.

Cleaning

1 round

trip of

wiper blade

1 round

trip of

wiper blade

Cleaning

Cleaning not performed

Cleaning interval

Содержание TS-1000-D





































Результаты поиска

Содержание TS-1000-D

Отзывы:

Похожие инструкции для TS-1000-D

Бренды по названию

Популярные бренды

Optex TS-1000-D, Инструкция по эксплуатации

Результаты поиска

Содержание TS-1000-D

Отзывы:

Похожие инструкции для TS-1000-D

Бренды по названию

Популярные бренды