background image

Interfaces

20

 

Sinergy S II Series Series UPS User Instruction Manual

AC FAIL 

This output provides an N/O (Normally Open) contact between pins 9 and 5, and an N/C (Normally 
Closed) contact between pins 8 and 5. The 9-5 contact closes when the mains voltage fails at the UPS input 
or when the mains voltage falls below the lower limit for a minimum of 10 seconds. This contact opens 
approximately 850 ms after the mains have been reestablished. The 8-5 contact provides a mirror function, 
opening when the mains voltage fails and closing when main power returns

LOW BATT 

This output provides a N/O contact between pins 6 and 5 and an N/C contact between pins 7 and 5. The 
6-5 contact closes when the battery has been depleted to the point that it can only supply current for 
approximately three (3) more minutes at nominal load. The 7-5 contact provides a mirror function opening 
when the battery is low.

BYPASS ACTIVE 

This output provides an N/O contact between pins 1 and 5. The 1-5 contact closes after switching to the 
bypass mode. In the bypass mode, energy to the output of the UPS is being supplied by the mains power 
and not through the inverter.

SUM ALARM 

This output provides an N/O contact between pins 2 and 5. The 2-5 contact closes when one of the alarms 
“AC FAIL,” “LOW BATT” or “BYPASS ACTIVE” is active or when the indication “ALARM” at the 
front-panel is on.

Содержание S07KXAU

































Отзывы: