One World Touch OP 1200, Руководство по обслуживанию

Страница: 132 / 135

Service Manual version 1008
OP 1200/1500/1700 (PC920 Intel 945G)
8-124
G: Power Supply
The power supply used in the OP SERIES system is a 250 watts (@25
o
C), 220 watt ((@50
o
C), AC-line
powered switching power supply with active PFC (Power Factor Correction) circuit. It meets
EN61000-3-2 and features with full range input. Its model number is FSP250-50PLB (1U) .
G-1: Output Electrical requirement
The subject power supply will meet all electrical specifications below, over the full operation
temperature range and dynamic load regulation.

Output Rating
250W 25
o
C
Output Nominal Regulation Ripple/Noise Min. Max. Peak
1 +3.3V +-5% 50mV 0.5A. 18.0A
2 +5V +-5% 50mV 0.3A 20.0A
3 +12V +-5% 120mV 1.0A 16.0A 18.0A
4 -12V +-5% 120mV 0.0A 0.5A
5 +5VSB +-5% 100mV 0.0A 2.0A 2.5A

-12V, 3.3V, +5V, +12V will have the regu-10% when all load take off

The +3.3V and +5V total output shall not exceed 150 watts. The +3.3V, +5V and +12V total
output shall not exceed 206.4 watts and the total output power for this subject power is 250
watts.
220W 50
o
C
Output Nominal Regulation Ripple/Noise Min. Max. Peak
1 +3.3V +-5% 50mV 0.5A. 14.0A
2 +5V +-5% 50mV 0.3A 18.0A
3 +12V +-5% 120mV 1.0A 14.0A 16.0A
4 -12V +-5% 120mV 0.0A 0.5A
5 +5VSB +-5% 100mV 0.0A 2.0A 2.5A

-12V, 3.3V, +5V, +12V will have the regu-10% when all load take off

The +3.3V and +5V total output shall not exceed 110 watts. The +3.3V, +5V and +12V total
output shall not exceed 206.4 watts and the total output power for this subject power is 220
watts.

Ripple and noise measurements shall be made under the specified load conditions through a
single pole pass filter with 20Mhz cutoff frequency. Outputs shall bypass at the connector with a
0.1uF ceramic disk capacitor and a 10uF electrolytic capacitor to simulate system loading.

Load Capacity Specification: The cross regulation defined as follows, the voltage regulation
limits DC includes DC output ripple & noise.
LOAD STM +3.3V +5V +12V -12V
ALL MAX HHHH 15.0A. 13.1A. 10.1A 0.5A
+5V MAX other MIN LHLL 0.5A 20.0A 3.0A 0.0A
+3.3 MAX other MIN HLLL 18.0A 0.3A 1.5A 0.0A
+12V MAX other MIN LLHL 0.5A 0.3A 16.0A 0.0A
ALL MIN. LLLL 0.3A 0.3A 1.0A 0.0A

Hold-up Time @ full Load
115V/60Hz 17 mSec. Minimum
230V/50Hz 17 mSec. Minimum

Output Rise Time
(10% to 90% of final output value, @ full load)
115V-rms or 230V-rms
+5Vdc=20ms Maximum