Omron CVM1 Series, Руководство по эксплуатации

Страница: 65 / 110

50
Replacement Checklists Section 3-6
3-6-1 Pattern A: Mixed Mid-sized and Large PLCs
The pattern A system contains mid-sized (C200H @ or CS-series) PLCs and
large (C500, C1000H, or C2000H) PLCs. Set the replacement PC Link Units
as shown in the following table.
Checklist 1
Use the following checklist when replacing a C500-LK009-V1 with a CVM1-
LK401.
Item Original Unit: C500-LK009-V1 Replacement Unit: CVM1-LK401 Remarks
CPU Bus
Unit unit
number Not applicable Any unique number in setting
range (Do not set the same unit
number on two CPU Bus Units in a
PLC.) Do not mount more PC
Link Units than allowed.
Node
address Check setting on pins 1 to 5: [ ] Set the CVM1-LK401’s node
address to the same node address
that was set on the C500-LK009-
V1. (Set the rotary switches in 2-
digit decimal.) Check the node address
settings on other nodes in
the PC Link to confirm
that the same address is
not already taken.
A Unit error will not occur
if the same node address
is set on two PC Link
Units in the same PC
Link, but there will be
data errors in the LR
Area.
Pins
1 to 5
Node
address
Pins
1 to 5
Node
address
00000 0 10000 16
00001 1 10001 17
00010 2 10010 18
00011 3 10011 19
00100 4 10100 20
00101 5 10101 21
00110 6 10110 22
00111 7 10111 23
01000 8 11000 24
01001 9 11001 25
01010 10 11010 26
01011 11 11011 27
01100 12 11100 28
01101 13 11101 29
01110 14 11110 30
01111 15 11111 31
Number of
LR Bits Check setting on pins 6 to 8 of SW1:
[ ] Bits / [ ] Units
Set the same number of LR bits
that was set on the C500-LK009-
V1. Make the “number of LR
bits” setting on the polling
node (node 0) in the PC
Link. The “number of LR
bits” settings on the other
nodes (polled nodes) are
ignored.
Set the same level/link
number (next item in
table) that was set on the
Unit being replaced. If an
invalid setting is set, the
max. valid number of bits
setting will be used
instead.
The number of Units
listed in parentheses for
the C500-LK009-V1 is the
maximum number of
Units for the C500 PLC.
The (*1) setting is invalid
for the C500.
Pins
6 to 8 Pin 3 of SW3 Pins
6 to 8 Pin 3
1 (Single-
level LK009) 0 (Multi-level) 1 (Single-
level LK009) 0 (Multi-
level)
000 32 bits/
32 (8) Units 32 bits/
16 (8) Units 000 32 bits/
32 Units 32 bits/
16 Units
001 64 bits/
16 (8) Units 64 bits/
8 (4) Units 001 64 bits/
16 Units 64 bits/
8 Units
010 128 bits/
8 (4) Units 128 bits/
4 (2) Units 010 128 bits/
8 Units 128 bits/
4 Units
011 256 bits/
4 (2) Units 256 bits/
2 (*1) Units 011 256 bits/
4 Units 256 bits/
2 Units
100 512 bits/
2 (*1) Units Invalid setting 100 512 bits/
2 Units Invalid set-
ting
101 Invalid set-
ting 101 Invalid set-
ting
110 110
111 111
NODE
No.
×
10
1
×
10
0
0
0