OmniTurn GT-75 Скачать руководство пользователя страница 20

Страница: 20 / 44

Pivot Bracket

Pushrod Adapter

Tray-guide

Shoulder

Tray Lock Knob

Home Stop

Shuttle Plate

Adjustable
Rear Stop

Spindle Liner

Adjustable

Tray Guide

Pusher

Micrometer
Adjust

Pushrod

Knee

Knee Adj Knob

zipldr_setup&operations

www.OmniTurn.com



[email protected]



(541) 332-7004



(541)-332-1018 fax

Fast... Precise... A

ﬀ

ordable...

Zip Loader Setup & Operations

Omni

Turn

Page 20 of 44

Using the Loader

Set the

Adjustable Home Stop

so that the pusher clears the bar or part when the shuttle is firmly against the stop.

The

Home sensor

must light when shuttle is firmly against the stop.

The

In Place sensor

is used in “part” and “stop” modes; it must light when part is at either front or rear stop.

The

Eject sensor

must light when the shuttle is at far right on rodless cylinder.

The

Cover Interlock Bypass

keyswitch (on PLC cabinet) allows testing setup with cover open.

Diameter change-over.

For best results, liner id and pusher od should be appropriate for the part or bar od. To

change liners, remove pushrod from shuttle plate (three 6-32 SHCS), then loosen the tray-lock knob, and remove mi-

crometer lock knob. Swing entire tray assembly up and out of the way to clear flange on liner. Liner is held in place

with o-rings; it can take some effort to remove it. Liners come with three o-rings; remove one closest for easier removal.

To put the bar or part on center of the spindle, loosen steel tray lock knob and micrometer lock knob (lower knob).

Slide part by hand from vee into liner, moving tray up or down with micrometer adjust until part slides smoothly.

The pivot brackets are held with tee-nuts, and can be moved if fine-tuning for very small part diameters is necessary.

Plastic knurled knobs on each side of tray assembly lock the “knee” of the guide channel “vee” at correct distance

for different diameter bars. Loosen knee adjustment knobs at each side of tray to adjust knife-to-vee distance for new

size bar. Manually cycle knife to insure smooth delivery of the bar.

For best results, use push-rod / pusher assembly that has pusher about same diameter as your stock. Matching

pusher to stock insures that pusher follows stock in vee and into liner properly.

Programming:

Detailed machine setup and programming information for the different modes starts on next page.

Содержание GT-75













































Результаты поиска

Содержание GT-75

Отзывы:

Похожие инструкции для GT-75

Бренды по названию

Популярные бренды

OmniTurn GT-75, Установка, эксплуатация и техническая документация

Результаты поиска

Содержание GT-75

Отзывы:

Похожие инструкции для GT-75

Бренды по названию

Популярные бренды