Omega CN76000, Руководство пользователя

Страница: 16 / 54

14
rES rES rES rES rES Automatic Reset Time. Select OFF OFF OFF OFF OFF, 0.1 0.1 0.1 0.1 0.1 to 99.9 99.9 99.9 99.9 99.9 minutes. Select OFF OFF OFF OFF OFF
to switch to O F S
O F S
O F S O F S O F S.
#OFS (948) or
O F S O F S O F S O F S O F S Manual Offset Correction Select O F F O F F O F F O F F O F F, , , , , 0.1 0.1 0.1 0.1 0.1 to 99.9% 99.9% 99.9% 99.9% 99.9%. Select OFF OFF OFF OFF OFF to
switch to rES rES rES rES rES.
#rtE (948) or
r r r r rtE tE tE tE tE Rate Time. Select O F F O F F O F F O F F O F F, , , , , 0.01 0.01 0.01 0.01 0.01 to 99.99 99.99 99.99 99.99 99.99 minutes, Deri vative.
S E C O N D S E C O N D
S E C O N D S E C O N D S E C O N DA R
A R
A R A R A RY MENU (cont'd)
Y MENU (cont'd)
Y MENU (cont'd) Y MENU (cont'd) Y MENU (cont'd)
S L O S L O S L O S L O S L O PID values are preset for a slow response process.
nor nor
nor nor nor PID values are preset for a normal response process.
F F F F FASt ASt ASt ASt ASt PID values are preset for a fast response process.
Pid2 Pid2
Pid2 Pid2
Pid2 Linkage of PID parameters between SP1 and SP2: Select O n O n
O n O n
O n or O F F O F F
O F F O F F
O F F.
O n O n O n O n O n Links SP2 to SP1 or #SP1 rEs and rtE terms for heat/cool applications.
O F F O F F O F F O F F O F F Sp2 functions without rEs and rtE.
ArUP ArUP ArUP ArUP ArUP Anti- Reset Wind-up Feature: Select O n O n O n O n O n or O F F O F F O F F O F F O F F.
O n O n O n O n O n When ArUP is On On On On On the accumulated Reset Offset value will be cleared to 0%
when the process input is not within the Proportional Band.
O F F O F F O F F O F F O F F When ArUP is O F F O F F O F F O F F O F F, the accumulated Reset Offset Value is retained in
memory when the process input is not within the Proportional Band.
Ar Ar
Ar Ar
ArtE tE
tE tE
tE Approach Rate Time: Select O F F O F F
O F F O F F
O F F, ,
, ,
, 0.01 0.01
0.01 0.01
0.01 to 99.99 99.99
99.99 99.99
99.99 minutes. The function defines the
amount of Rate applied when the input is outside of the Proportional Band. The ArtE
time and the rtE time are independent and have no effect on each other. To
increase damping effect and reduce overshoot set the approach rate time for a value
greater than the natural rise time of the process (natural rise time = process value
time to set point).
P E A P E A P E A P E A P E A The Peak feature will remember the highest input the Instrument has had since the
last reset or Pow er On. At Pow er On it is reset to the present input.
To manually reset
the value, PEA must be in the low er display and then press the E N T E R E N T E R
E N T E R E N T E R
E N T E R key. This will
cause PEA to be reset to the present input value.
U U
U U U A L
A L
A L A L A L The Valley feature will remember the low est input the Instrument has had since the
last reset or Pow er On. At Pow er On it is reset to the present input, and may have
to be manually reset.
To manually reset the value, VAL must be in the low er display
and then press the E N T E R E N T E R E N T E R E N T E R E N T E R key. This will cause UAL to be reset to the present input
value.
In the following the symbol "#" will be used following letters to refer to either a number "1"
or number "2".
The "1" will relate to SP1 functions, the "2" for SP2. If your control is not
equipped with a second set point, no SP2 functions will appear. The appearance of CY#
CY#
CY# CY# CY#,
SP#d SP#d
SP#d SP#d
SP#d, or PUL# PUL#
PUL# PUL#
PUL# is dependent upon the output type selected in the Secure Menu item S#Ot.
If time proportioning (cycle time) was selected, then CY# is adjustabl e. If On - Off was
selected, then SP#d is adjustabl e. If pulsed time proportioning was selected then PUL# is
OUTPUT
0
REVERSE ACTING (S#St = rE)
(DOWNSCALE DIFFERENTIAL)
INPUT
SP# (DISPLAYED VALUE)
DIFF.
(SP#d)
OUTPUT
0 INPUT
SP# (DISPLAYED VALUE)
DIFF.
(SP#d)
DIRECT ACTING (S#St = dir)
(UPSCALE DIFFERENTIAL)