OMEGA AIR A-DRY Series страница 7 Скачать руководство пользователя

Страница: 7 / 65

1.6 Appropriate use

DRY series desiccant dryers are intended for highly efficient preparation of top
quality dry compressed air. This appliance must be used only for the purpose for
which it was specifically designed. All other uses are to be considered incorrect.

Specifically:

•

Desiccant dryer can only be used for “GROUP 2” fluids (PED 2014/68/EU).

•

Desiccant dryer can not be used for explosive, toxic, flammable, corrosive and
“GROUP 1” fluids (PED 2014/68/EU).

Warning: internal corrosion can seriously reduce the safety of installation: check it during
maintenance.

The manufacturer will under no circumstances be responsible for any damage resulting from
improper, incorrect or unreasonable use.

Use genuine spare parts only. Any damage or malfunction caused by the use of non-genuine
parts is not covered by Warranty or Product Liability.

Содержание A-DRY Series


































































Результаты поиска

Содержание A-DRY Series

Отзывы:

Похожие инструкции для A-DRY Series

Бренды по названию

Популярные бренды

OMEGA AIR A-DRY Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание A-DRY Series

Отзывы:

Похожие инструкции для A-DRY Series

Бренды по названию

Популярные бренды