10014 Planer
OLIVERMACHINERY.NET
13
|
Page
Safety
Oliver Machinery has made every attempt to provide a safe, reliable, easy-to-use piece of machinery.
Safety, however, is ultimately depending on the individual machine operator.
Before operating this
machine, please become familiar with the following safety labels and guidelines.
DANGER
This indicate an imminent hazardous situation which, if not avoided,
WILL
cause
death or serious injury.
WARNING
This means if the warning is not taken seriously, it
CAN
cause death or serious
injury.
CAUTION
This mean if the precaution is not taken, it
MAY
cause minor or moderate injury.
IMPORTANT
This is a tip about proper operation of the machine to avoid machine damage.
General Safety Guidelines
1.
FAMILIARIZE
yourself with all safety instructions found in this manual. Know the limitations and
hazards associated with this machine. Do not operate / service this machine until you are properly
trained.
2.
ELECTRICAL GROUNDING
, when done properly, reduce the risk of electrocution, shocks and fire.
Make certain that the machine frame is electrically grounded and that a ground lead is included in
the incoming electrical service. In cases where a cord and a plug are used, make certain that the
grounding plug connects to a suitable ground. Follow the grounding procedure indicated in the
electrical code of your area.
3.
DISCONNECT
the machine from power before performing any service, maintenance, or adjustments.
A machine under repair should be RED TAGGED to show it should not be used until the repair is
complete.
4.
EYE PROTECTION
: Always wear an approved safety face shield, goggles, or glasses that complies
with ANSI Z87.1 and CSA Z94.3 standards. Common eyeglasses are not safety glasses, and may not
provide adequate protection.
5.
EAR PROTECTION
: Use hearing protective devices where the noise exceeds the level of exposure
allowed in Section 1910.95 of the OSHA Regulations. When in doubt, use it.
6.
OTHER PERSONAL PROTECTION
: Before operating the machine, remove tie, rings, watch and other
jewelry. Roll up sleeves above the elbows. Remove all loose outer clothing and confine long hair.
Protective type footwear should be used. Do not wear gloves unless it is instructed to perform
particular step(s) in the manual.
7.
GUARDS
: Keep the machine guards in place for all applicable operations. If any guards are removed
for maintenance, DO NOT OPERATE the machine until the guards are reinstalled. Check clearance
between the guards and the cutter before starting the machine.
8.
WORKPLACE SAFETY
: Keep the floor around the machine clean. Scrap material, saw dust, oil and
other liquids increase the risk of tripping or slipping. Be sure to clean up the table before starting the
machine. Make certain the work area is well lighted and that a proper exhaust system is used to
Содержание 10014
