![background image](http://html1.mh-extra.com/html/okidata/ol1200ex/ol1200ex_service-manual_3678465058.webp)
%3.3.14 Front Feeder Roller Assy
3.3.14 Front feeder roller Assy
(1) Turn the AC power supply switch off. Unplug the AC power cord from the outlet.
(2) Remove the manual feed hopper Assy (see 3.3.4).
(3) Remove the side cover (R) (see 3.3.5).
(4) Remove the front feeder roller Assy (see 3.3.12 (1) to (3).
(5) Remove the paper supply guide A (see 3.3.13 (1) to (10)).
(6) Remove idle gear 1 and then remove the right side front feeder cam 2, release lever (R) 3, and
spring 4. (At this time, knock pin 5 and bearing F are also removed. Be careful not to lose them.)
Do not mix these parts with those from the left side of Assy.
(7) Pull out the front feeder 7 shaft toward the left and then remove front feeder roller Assy 8.
(8) Remove knock pin 9 and then remove front feeder cam D on the left (L) side, release lever (L) A,
and spring B. (At this time, the bearing C on the left (L) side is also removed.) Do not mix these
parts with those from the right side of Assy.
Note
1: Hopping roller orientation when removed from shaft.
2: Be sure sensor arm swings freely after re-assembly.
3: Be sure that during re-assembly both feeder cams (2 and D) are facing the same direction.
Содержание OL1200ex
