![background image](http://html1.mh-extra.com/html/okidata/ol1200ex/ol1200ex_service-manual_3678465147.webp)
%6. Print voids
6. Print voids
Is the contact plate of the transfer roller contacted with the power/sensor board properly?
(See Figure 6-5.)
No
Adjust the contact plate contact to contact the power/sensor board properly and
the shaft of the transfer roller.
t
Yes
Replace the transfer roller. (See 3.3.36.)
Has the trouble been removed.
Yes
End
t
No
Are the contacts of the toner supply roller, developing roller, image drum and charging
roller contacted with the contact assy properly?
(See Figure 6-5 A, B, C, D, E.)
No
Adjust the contacts to contact the contact assy properly.
t
Yes
Replace the image drum cartridge.
Has the trouble been removed?
Yes
End
Note:
After replacing the image drum cartridge, set the printer in the user
maintenance mode by turning the power on while pressing the MENU
key, and reset the drum counter. (Refer to Users Manual.)
t
No
Is the LED head installed properly?
(Check connector HEAD1(14p), HEAD2 (12p)
on the control board and PC Connec- tor on the
LED head.)
No
Install the LED head properly.
t
Yes
Replace the LED head or the head cable.
Has the trouble been removed?
Yes
End
Note:
After replacing the LED head, set the printer in the engine maintenance
mode by turning the power on while pressing the FORM FEED and
ENTER keys. Set the LED head drive time. (Refer to Section 4.2.)
t
No
Replace the control board (OLCW- ) or power/sensor board.
Содержание OL1200ex
