![background image](http://html1.mh-extra.com/html/okidata/ol1200ex/ol1200ex_service-manual_3678465085.webp)
%4.1 Maintenance Modes And Functions
4.1 Maintenance Modes And Functions
• User maintenance mode
To enter the user maintenance mode, turn on the POWER switch while pressing the MENU key.
Function
There are six functions as follows.
• Menu reset
• Hex dump
• Drum counter reset
• Operator panel menu disable
• X adjust
• Y adjust
• System maintenance mode
Note: This mode is used only by service persons and it should not be released to the end-users.
To enter the system maintenance mode, turn on the POWER switch while pressing the RECOVER
key.
Function
There are five functions as follows.
• Page count display
• Loop test
• Page count printing enable/disable
• EEPROM reset
• Rolling ASCII continus prinitng
• Engine maintenance mode
Note: This mode is used only by service persons and it should not be released to the end-users.
To enter the engine maintenance mode, turn on the POWER switch while pressing the FORM
FEED key and ENTER key.
Function
There are 13 functions as follows.
• Head drive time setting
• Printing start position setting
• Drum counter total display
• Drum count display
• Setting of standard paper feed length
• Setting of front feeder paper feed length
• Setting of second tray paper feed length
• Selection of second tray feeder download table
• Setting of envelope feeder paper feed length
• Selection of envelope feeder download table
• Fuser count indication
• Fuser count reset
• Engine reset
Содержание OL1200ex
