![background image](http://html1.mh-extra.com/html/okidata/ol1200ex/ol1200ex_service-manual_3678465115.webp)
%LCD Status Messages: (2-4) General
%LCD Status Messages: (2-4) General
Category
LCD Status Message
Trouble of Status
Remedy
Paper
request
Loading of paper indicated by the
first line message is requested.
• Load the requested paper in
the tray.
Tray paper
out
The tray has run out of paper.
tttttt: Tray being selected
(TRAY1, TRAY2,
FRONT, MANUAL, ENVLOP)
• Load a paper or a paper
cassette to the tray.
Buffer
overflow
The memory was overflowed due to
the following causes.
- Data to be printed in one page is
too much.
- Macro data is too much
- DLL data is too much.
• Press the RECOVER key on
the operator panel to release
the error display.
• Install an expansion optional
RAM or reduce the amount of
print data.
Buffer
overflow
The receive buffer was overflowed
• Press the RECOVER key on
the operator panel to release
the error display.
• Chang the setting of the host
side so that the host can detect
the busy state of the printer.
Resend the data from the host
side to the printer.
Buffer
overflow
The printer overrun.
• Press the RECOVER key on
the operator panel to release
the error display.
• Simplify page data
fomatting.
Interface
error
An error occurred in the serial I/F.
This message is displayed when a
parity error, a framing error or an
overrun error is detected.
• Press the RECOVER key on
the operator panel to release
the error display.
• Check the settings of
RS232C I/F in the menu.
• Replace the interface cable
or Control board.
Note:
When replacing
the Control board, install the
EEPROM mounted in the
replaced Control board.
Card
removal
error
The card containing print data was
removed.
• Install the card again.
Содержание OL1200ex
