![background image](http://html1.mh-extra.com/html/okidata/ol1200ex/ol1200ex_service-manual_3678465138.webp)
%8. Data from the host not received via the serial interface.
8. Data from the host not received via the serial interface.
Is message
displayed?
Yes
Select the auto interface or RC232C for the host interface in menu level 1.
t
No
Do the following items selected for RS232C SERIAL in menu level 2 coincide with
those selected at the host side?
FLOW CONTROL
PARITY
BAUD RATE
MIN. BUSY
DATA BITS
NO
If the selection differs between the printer and the host, change the setting of the
above items in menu level 2 so as to coincide with the setting at the host side.
t
Yes
Is the connector of the serial interface cable connected to the printer properly?
No
Connect the connector of the serial interface cable to the printer properly
t
Yes
Is there any defect in the serial interface cable (broken or bent pin, broken wire)?
Yes
Replace the serial interface cable.
t
No
Perform the loop back test using the loop test function in the system maintenance
mode. (To make this test, it is necessary to form the following loop back connector.
Connect the loop back connector to port instead of connecting the host.)
t
Is
displayed?
Yes
Replace the serial interface cable.
t
Is the printer recovered?
YES END.
t
No
Replace the Control board.
t
No
Replace the Control board or ask the user to check the hardware and software at the
host side.
Содержание OL1200ex
