%3.3.08 Forms Tear Off
3.3.08 Forms Tear Off
General Information
This feature (when activated) will automatically advance continuous feed paper to the tear-off position
after it finishes printing the last page in the document. A few seconds after the printing stops, the printer
will move the paper up to the tear-off position, aligning the perforation with the serrated edge on the
access cover. The operator will be able to tear off the last printed page without wasting paper or
readjusting the printer. When the printer receives data to print, it will automatically return the paper to the
top of form position for printing.
Forms Tear Off can only be used with continuous feed paper fed in from the rear on the built-in push
tractor. It CANNOT be used with the optional pull tractor.
NOTES:
Some programs, such as high resolution graphics packages, pause occasionally while sending data to
the printer.
If the pause lasts more than the selected interval, the paper will advance to the tear-off position until more
data is received.
No data is lost, but the extra paper movement causes uneven print registration.
If this problem occurs, disable (set to OFF) the Menu Setting for Forms Tear Off.
Procedure
1. Load continuous feed paper into the printer.
2. Verify that the ribbon is installed.
3. Power ON the printer.
4. Verify that the printer is ON-LINE (SELECT lamp is lit).
5. Press SELECT and place the printer OFF-LINE (SELECT will
not be lit).
6. Press QUIET to enter Menu Mode.
7. The line shown below will print.
Printer Control Emulation Mode <current setting> 8. Press GROUP until the following line is printed.
General Control Graphics <current setting> 9. Press ITEM until the following line is printed.
General Control Forms Tear Off <current setting> 10. Press SET to change the menu setting for Forms
Tear Off.
To activate Forms Tear Off, the setting must be 300 mS, 2 sec., or 4 sec. To deactivate Forms Tear Off,
the setting must be OFF. 11. Press EXIT to exit Menu Mode.
12. The printer will go ON-LINE. (SELECT will light.)
Application of the Forms Tear Off Feature
Point of Sale
1. Set menu selection General Control, Forms Tear Off, to OFF-LINE.
2. The printer will print the receipt.
3. The printer will advance the receipt to the tear off position and go OFF-LINE.
4. Tear off the receipt.
5. Press SELECT to place the printer ON-LINE.
Continuous Invoices
6. Set menu selection General Control, Forms Tear Off, to 300 ms.
7. The printer will print the invoices without stopping.
8. If the final invoice does not print, issue a FORM FEED command at the end of the job. This will force
the last invoice to the print position to complete the job.
NOTE:
The page will be advanced to the tear off position after waiting two or four seconds (depending on the
menu selection) for a print signal. The paper will then be retracted to the next print position.
ML395 ( 96-02-03 )
Содержание Microline 395
