manualshive.com logo in svg

Oki B431L6, Руководство по обслуживанию

Поделиться
Скачать
Oki B431L6 Скачать руководство пользователя страница 85

4. ADJUSTMENT

Oki  Data  CONFIDENTIAL

44983601TH  Rev.1 

4-6 /

4.1.2  System maintenance mode (System maintenance menu)

Note!

    • This mode is only used by maintenance personnel; it is not released to the end user. 

 

• This mode is only B431.

 

• Refer to "Maintenance Utility" for B401/B411.

 

• (*1) can be set by "Maintenance Utility".

To open System Maintenance Menu, hold down the "MENU  " and "MENU  " button and turn on the power 
switch. After the Category has been displayed, let go of the "MENU  " and "MENU  " button.

Category

Operation panel display

Default 

value

Function

 

* Only English is supported for panel 

display

Setting item 

(Upper case)

Setting item 

(Lower case)

OKIUSER

(*1)

OKIUSER

ODA 

OEL

 

APS 
JP1 
JPOEM1 
OEMA 

OEML

*

Set the destination. 
JPOEM1: Japan Oriented OEM
OEMA: Overseas OEM for A4 default 

OEML: Overseas OEM for Letter default 
After passing the MENU, it reboots 
automatically. If the Japanese font exist, JP1 is 

default.

MAINTENANCE 
MENU

FLASH FORMAT EXECUTE

-

Initialize Flash ROM. 
After executing it passes the MENU. The 
format of Flash Device that is implemented on 

resident (on board) starts. 

MENU RESET

EXECUTE

-

Reset the EEPROM content to the (Factory 

Default) setting value . After the setting 

alteration, it reboots automatically. 

 Part of special item is not initialized.

CONFIG MENU

CODESET

TYPE1 
TYPE2

* 

This MENU displays as all destination. 
TYPE1: Non display of Russian / Grace

TYPE2: Display Russian / Grace. 

After passing the MENU, it reboots 

automatically.

For destination of OEL/APS/OEMA, TYPE2 is 

default value.

For other destinations, TYPE1 is default value.

TEST PRINT 
MENU

TEST PRINT 
MENU

ENABLE

 

DISABLE

 

*

Switch between whether to display ENGINE 
INFORMATION that is on the INFORMATION 
MENU Category of USER MENU. If this item is 
Disable, ENGINE INFORMATION is not often 

displayed.

FUSE KEEP 

MODE

FUSE KEEP 

MODE

EXECUTE

-

While press ENTER Key the command is send 
from CU to PU and then it becomes ONLINE. 

Replace the consumable by the new one and 

check the operation as the power ON. (At this 
moment, the fuser of new consumable is not 

cut and the operation count is not added to the 
value of old consumable. 

While turn the power OFF the check mode is 

terminated.

Till the next time of power ON it is Disable.

Содержание B431L6

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды