manualshive.com logo in svg

Oki B431L6, Руководство по обслуживанию, Страница: 177 / 184

Поделиться
Скачать
Oki B431L6 Скачать руководство пользователя страница 177

Appendix C Maintenance Manual for Second Tray unit

Oki  Data  CONFIDENTIAL

44983601TH  Rev.1 

Appendix C-16 /

Table 5-1 List of Statuses and Trouble of Second Tray unit

Category

LCD Status 

Message

LED

Trouble or Status

Handling

(English)

Ready

Atten

Jam Error

(Paper 
Feeding)

OPEN UPPER
COVER
392:PAPER JAM

OFF

Blinking

Notifies that a jam 

occurs during the 
paper feed from the 

Second Tray unit.

•  Check paper in the 

Second Tray unit.

  Open and close the 

top cover to recover 

printing, and delete the 

error display.

•  If it occurs frequently, 

take action according 

to the troubleshooting 
flow.

Jam Error

(Paper path)

OPEN UPPER 
COVER

 

nnn:PAPER JAM

 

 
*nnn:381/382/389

OFF

Blinking

Notifies that a jam 

occurs while paper 
is running through 
the paper path.

•  Check paper in the 

extended paper feed 
unit.

  Open and close the 

top cover to recover 

printing, and delete the 

error display.

Jam Error
(DUPLEX)

OPEN REAR 
COVER

 

372:PAPER JAM

OFF

Blinking

Notifies that a 
jam occurs while 

printing from the 
duplex unit.

•  Check paper in the 

extended paper feed 
unit.

  Open and close the 

top cover to recover 

printing, and delete the 

error display.

Size Error

LOAD mmmm/
pppp AND PRESS 
ONLINE SWITCH

 

462:TRAY2 MEDIA 
MISMATCH

OFF

Blinking

Notifies that the 
paper size during 

the paper feeding 

from the Second 

Tray unit is not 
correct.

•  Check ht epaper in the 

Second Tray unit.

  In addition, check if the 

paper is not overlapped. 
Open and close the 
top cover to recover 

printing, and delete the 

error display.

OPEN UPPER 
COVER

 

nnn:PAPER JAM

 

 
*nnn: 
380/381/382/389

OFF

Blinking

Media Error

LOAD mmmm/
pppp AND PRESS 
ONLINE SWITCH

 

462:TRAY2 MEDIA 
MISMATCH

OFF

Blinking

The media type in 

the Second Tray 

unit is different from 
the edition media 
type.

•  Load paper requested 

to the Second Tray unit.

Tray Paper 
Out

 

TRAY2 EMPTY

Not

determined

ON

Notifies that there 

is no paper in the 

Second Tray unit.

•  Load paper in the 

Second Tray unit.

LOAD mmmm

 

492:TRAY2 EMPTY

OFF

Blinking

5.3.1  LCD Status Message List

The list of statuses and trouble displayed as the message format in LCD is outlined in Table 5-1.

Содержание B431L6

























































































































































































Отзывы:

Нет отзывов