Oki B431L6 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 184

Oki B431L6 Скачать руководство пользователя страница 106

4. ADJUSTMENT

Oki Data CONFIDENTIAL

44983601TH Rev.1

4-27 /

4.1.5 EEPROM Initialization

The treatment for EEPROM Initialization at each phenomenon is displayed as Diagram 4-1.

Diagram 4-1 EEPROM Initial Setting Range

No

Phenomenon

CU EEPROM Area

PU EEPROM Area

Factory

Default

Area

User

Menu

Area

OP

Menu

Area

Administrator Menu/

System Maintenance

Menu Area (*3)

F/W

Revision

Area

Engine Maintenance Menu Area

Brands

Area

Drum

Counter

Page

Counter

Toner

Dot

Counter

1

User Maintenance Menu

EEPROM RESET
Operation

−

−

−

−

−

−

−

−

−

2

F/W Revision check error

at the time of a power on.

−

−

(*4)

−

−

−

−

−

3

CU EEPROM area

mapping
Revision check error at the
time of a power on.

(*4)

−

−

−

−

−

−

4 Brands area check error at

the time of a power on. (*1)

(*4)

−

−

−

−

5 Engine Maintenance Menu

ENGINE RESET

Operation

−

−

−

−

−

−

−

(*2)

(*5)

6

PU EEPROM area

mapping check error at
the time of a power on.

−

−

−

−

−

−

(*3)

7 System Maintenance

Menu
EEPROM RESET
Operation

−

(*4)

−

−

−

−

−

−

(*1) Destination Check is for the operation on the different product (destination) with the previously operated product

(destination). It is the reset relying on the recognition regarding the destination change by PJL command and the
operation at POWER ON of the new product EEPROM as an error.

(*2) It is reset to 0 limited by Page Count less than 500 pieces. (ENGINE RESET due to PJL Command is not in this

limitation.)

(*3) About DOT SHIFT setting menu, even it is also exist in System Maintenance Menu, but because the setting

value keeping area is allocated in PU EEPROM AREA, in the case of the item of System Maintenance Menu
initialized, DOT SHIFT setting is not initialized. By contraries, in the case of PU EEPROM AREA initialized, DOT
SHIFT setting is initialized.

(*4) DOT SHIFT setting should not be initialized.

(*5) Because of the support of Toner TAG, Toner Dot Counter is not reset.

«
...
104
105
106
107
108
...
»

Содержание B431L6

























































































































































































Отзывы:

Нет отзывов