Oki B431L6 Скачать руководство пользователя страница 120

Страница: 120 / 184

6. Procedures for Repairing

Oki Data CONFIDENTIAL

44983601TH Rev.1

6-11 /

The case where the printer does not work normally after tuning on the power

• Turn off the power and then, turn on the power again.

• Are messages in the display of LCD all in black?

• NO

Is the AC cord properly connected?

• NO

Connect the AC cord.

• Yes

Is the cable to connect the main board with the low-voltage power correctly
connected?

•

Connect the cable.

• Yes

Is +5V supplied to the main board?

(Check with 18 pins and 35 pins of CENT connector)

• No

Do+5V of the main board and GND short out?

(Check with 18 pins and 35 pins of CENT connector)

Replace the low-voltage power.

• Yes

Replace the main board.

• Yes

The flexible cable of the operator panel Assy is appropriately connected to the

LCDPNL connector of the main board and Connector CN1.

• No

Connect the flexible cable appropriately.

• Yes

Replace the operator panel Assy or the flexible cable.

• Has the problem been solved?

• No

Replace the main board.

• Yes

Completed

• Yes

Is the message of "INITIALIZING" displayed on the LCD?

• No

Replace the main board.

• Yes

Is the message of "ONLINE" is displayed on the LCD?

• No

Take action according to the LCD status message/ Trouble List. (Refer

to the Section 6.5.1 for how to take action.)

• Yes

Completed.

Содержание B431L6

























































































































































































Результаты поиска

Содержание B431L6

Отзывы:

Oki B431L6, Руководство по обслуживанию, Страница: 120 / 184

Результаты поиска

Содержание B431L6

Отзывы: