Oki B431L6 Скачать руководство пользователя страница 129

Страница: 129 / 184

6. Procedures for Repairing

Oki Data CONFIDENTIAL

44983601TH Rev.1

6-20 /

The white section is dirty

• Is the image drum exposed by the external light?

• Yes

Install the image drum in the printer and wait 30 minutes.

• No

From [MAINTENANCE MENU], select [PAPER BLACK SET] - [SMR SETTING] and set a

larger value for adjustment.

• Has the trouble been solved?

• Yes

Completed.

• No

From [MAINTENANCE MENU], select [SMR SETTING] and set a smaller value for

adjustment.

• Has the trouble been solved?

• Yes

Completed.

• No

Is the heat roller of the fuser unit assy dirty?

• Yes

Clean the heat roller.

• Has the trouble been solved?

• Yes

Completed.

• No

Replace the image drum cartridge.

• Has the trouble been solved?

• Yes

Completed.

• No

Replace the main board, high-voltage power/ sensor board.

White paper is outputted

• Is the LED head appropriately connected? (Check the HEAD connector of the main board and the PC

connector of the LED head.)

• No

Connect the LED head appropriately or replace the head cable.

• Yes

Is the image drum cartridge appropriately connected to the earth contact? (See Figure 6-3

)

• No

Adjust the earth contact (drum) of the contact assembly.

• Yes

Replace the LED head.

• Has the trouble been solved?

• Yes

Completed.

• No

Replace the main board or high-voltage power supply unit.

Содержание B431L6

























































































































































































Результаты поиска

Содержание B431L6

Отзывы:

Бренды по названию

Популярные бренды

Oki B431L6, Руководство по обслуживанию

Результаты поиска

Содержание B431L6

Отзывы:

Бренды по названию

Популярные бренды