manualshive.com logo in svg

Oki B431L6, Руководство по обслуживанию, Страница: 183 / 184

Поделиться
Скачать
Oki B431L6 Скачать руководство пользователя страница 183

Appendix D Network Interface

Oki  Data  CONFIDENTIAL

44983601TH  Rev.1 

Appendix D-3 /

Operation Panel Display

Default

Function

Items

Setting value

SUBNET MASK

xxx.xxx.xxx.xxx

-

Set the subnet mask.
[Display Conditions]

  • "TCP/IP" is enabled, and "IP VERSION" is IP v4 or IPv4+v6.

GATEWAY 
ADDRESS

xxx.xxx.xxx.xxx

*

Set the gateway address.
[Display Conditions]

  • "TCP/IP" is enabled, and "IP VERSION" is IP v4 or IPv4+v6.

WEB

ENABLE 
DISABLE

*

Specify Enable/ Disable of WEB.
[Display Conditions]

  • "TCP/IP" is enabled.

TELNET

ENABLE 
DISABLE

*

Specify Enable/ Disable of TELNET.
[Display Conditions]

  • "TCP/IP" is enabled.

FTP

ENABLE 
DISABLE

*

Specify Enable/ Disable of FTP.
[Display Conditions]

  • "TCP/IP" is enabled.

SNMP

ENABLE 
DISABLE

*

Specify Enable/ Disable of SNMP.
[Display Conditions]

  • "TCP/IP" or "NETWARE" is enabled.

NETWORK SCALE NORMAL 

SMALL

*

Normal: usually, this setting is used.
In the NORMAL, even if connected to the HUB having the spanning tree 
function, the device operates efficiently. However, when the computer is 
connected to two or three small LANs, it takes long to start a computer. 
At SMALL, the computer supports two or three small LANs and large 
LAN, however, when connected to the HUB having the spanning tree 
function, the device may not operate efficiently.

HUB LINK 
SETTING

AUTO NEGOTIATE 
100BASE-TX FULL 
100BASE-TX HALF 
10BASE-T FULL 
10BASE-T HALF

*

Set a method of link to the HUB.
When setting to Auto, the connection method is automatically  selected 
for all of the HUB, and connection is tried.
When selecting other items, the connection to the HUB is tried only by 
the connection method.

TCP ACK 

TYPE1
TYPE2

*

Set the type of TCP Acknowledgment.
When Type1 is set, the printer replies  to every packet.
When Type2 is set, the printer replies  to plural packets in a mass. 
When printing comes to take time by the setting of the hub, choosing 
Type2 may improve the matter.
Usually, setting Type1 hasn't any problem.
[Display Conditions]

• "TCP/IP" is enabled.

FACTORY 
DEFAULTS

EXCUTE

-

Initialize the network menu.

Содержание B431L6

























































































































































































Отзывы:

Нет отзывов