OHTAKE NSRI Series, Руководство по эксплуатации

Страница: 7 / 36

- 6 -
Check if the machine has the parts which match the nominal diameter
of the screws to be loaded. Check the model number of the rail,
escaper, escaper guide for the robot and passing plate by referring to
the following table. Each escaper is stamped with a model number
which matches with the type of screws that can be used. The escaper
guide for the robot is stamped with a model number which
corresponds with the types of screws that can be used.
５．
ADJUSTMENTS AND CHECKS BEFORE USE
５ -
１
． Checking the model number of the main body
Rail
identification
seal
Passing plate identi-
fication seal
Before delivery, each section of the machine is checked and adjusted with panhead screws matching the nominal
diameters of the ordered model.
Most screws may be usable in the initial status of adjustment however, if the height or shape of the screw head is
different or if the operation is regarded as abnormal, each section must be readjusted. If this is the case,
make the following checks and adjustments:
○ Check the screw load amount ○ Check and adjust the brush ○ Check and adjust the passing plate
○ Check and adjust the rail vibration ○ Check and adjust the holding plate
○ Check and adjust the front & rear sides of the rail ○ Check and adjust the timer
If the rail, escaper, passing plate and robot escaper guide are replaced, screws with a different nominal diameter can be
accepted. After these parts are replaced, fine adjusting is required. The respective adjusting procedures will be described
elsewhere. Please read these procedures.
Note: Screws, with a different nominal diameter, can be used by replacing the rail,
escaper, passing plate and the robot escaper guide for the robot.
The parts, for replacement, are available separately.
Escaper identi-
fication stamp
Escaper guide for
the robot identifica-
tion stamp
㻾㼑㼒㼑㼞㼑㼚㼏㼑㻌㼠㼍㼎㼘㼑㻌㼛㼒㻌㼠㼔㼑㻌㼟㼜㼑㼏㼕㼒㼕㼑㼐㻌㼟㼏㼞㼑㼣㼟
㻿㼏㼞㼑㼣
㼒㼑㼑㼐㼑㼞
㼟㼑㼞㼕㼑㼟
㻿㼏㼞㼑㼣
㼒㼑㼑㼐㼑㼞
㼙㼛㼐㼑㼘
㻿㼏㼞㼑㼣㻌㼟㼕㼦㼑
㻱㼤㼏㼔㼍㼚㼓㼑
㼗㼕㼠㻌㻺㼛㻚
㻾㼍㼕㼘㻌㼙㼛㼐㼑㼘
㻺㼛㻚
㻱㼟㼏㼍㼜㼑㼞
㼙㼛㼐㼑㼘㻌㻺㼛㻚
㻾㼛㼎㼛㼠
㼑㼟㼏㼍㼜㼑㼞㻌㼓㼡㼕㼐㼑
㼙㼛㼐㼑㼘㻌㻺㼛㻚
㻼㼍㼟㼟㼕㼚㼓㻌㼜㼘㼍㼠㼑
㼙㼛㼐㼑㼘㻌㻺㼛㻚
㻿㼏㼞㼑㼣
㼟㼕㼦㼑
㻿㼏㼞㼑㼣
㼟㼔㼍㼒㼠
㼐㼕㼍㼙㼑㼠㼑㼞
（
φ
）
㻿㼏㼞㼑㼣
㼔㼑㼍㼐
㼐㼕㼍㼙㼑㼠㼑㼞
（
φ
）
㻿㼏㼞㼑㼣
㼔㼑㼍㼐
㼠㼔㼕㼏㼗㼚㼑㼟㼟
（mm）
㻿㼏㼞㼑㼣㻌㼟㼔㼍㼒㼠
length（mm）
㻿㼑㼙㼟
㻰㼛㼡㼎㼘㼑
㼟㼑㼙㼟
㼃㼍㼟㼔㼑㼞
㼔㼑㼍㼐
㻺㻿㻾㻵㻝㻜 㻹㻝㻚㻜 㻾㻵㻝㻜㻿㻱㼀 㻾㻵㻝㻜 㻿㻵㻱㻝㻜 㻹㻝㻚㻜 0.9～0.95 1.2～4.5 0.35～1.0 1.6～10 ○
㻺㻿㻾㻵㻝㻞 㻹㻝㻚㻞 㻾㻵㻝㻞㻿㻱㼀 㻾㻵㻝㻞 㻿㻵㻱㻝㻞 㻹㻝㻚㻞 1.1～1.15 1.4～4.5 0.35～1.0 1.8～10 ○
㻺㻿㻾㻵㻝㻠 㻹㻝㻚㻠 㻾㻵㻝㻠㻿㻱㼀 㻾㻵㻝㻠 㻿㻵㻱㻝㻠 㻹㻝㻚㻠 1.3～1.4 1.7～4.5 0.35～1.0 2.0～10 ○
㻺㻿㻾㻵㻝㻣 㻹㻝㻚㻣 㻾㻵㻝㻣㻿㻱㼀 㻾㻵㻝㻣 㻿㻵㻱㻝㻣 㻹㻝㻚㻣 1.6～1.7 2.0～4.5 0.35～1.0 2.3～10 ○
㻺㻿㻾㻵㻞㻜 㻹㻞㻚㻜 㻾㻵㻞㻜㻿㻱㼀 㻾㻵㻞㻜 㻿㻵㻱㻞㻜 㻹㻞㻚㻜 1.9～2.1 2.4～6 0.35～4.5 2.6～20 ○ ○ ○ ○ ○ ○ ○
㻺㻿㻾㻵㻞㻟 㻹㻞㻚㻟 㻾㻵㻞㻟㻿㻱㼀 㻾㻵㻞㻟 㻿㻵㻱㻞㻟 㻹㻞㻚㻟 2.2～2.4 2.7～6 0.35～4.5 2.9～20 ○ ○ ○ ○ ○ ○ ○
㻺㻿㻾㻵㻞㻢 㻹㻞㻚㻢 㻾㻵㻞㻢㻿㻱㼀 㻾㻵㻞㻢 㻿㻵㻱㻞㻢 㻹㻞㻚㻢 2.5～2.7 3.0～6 0.35～4.5 3.2～20 ○ ○ ○ ○ ○ ○ ○
㻺㻿㻾㻵㻟㻜 㻹㻟㻚㻜 㻾㻵㻟㻜㻿㻱㼀 㻾㻵㻟㻜 㻿㻵㻱㻟㻜 㻹㻟㻚㻜 2.9～3.2 3.5～6 0.35～4.5 3.6～20 ○ ○ ○ ○ ○ ○ ○
使用ネジ
の呼び
ピッチ
外形min
㻞 㻜㻚㻠 㻜㻚㻜㻥㻡 㻝㻚㻥㻝
㻞㻚㻟 㻜㻚㻠 㻜㻚㻜㻥㻡 㻞㻚㻞㻝
㻞㻚㻢 㻜㻚㻠㻡 㻜㻚㻝 㻞㻚㻡㻜
㻟 㻜㻚㻡 㻜㻚㻝㻜㻢 㻞㻚㻤㻥
㻟㻚㻡 㻜㻚㻢 㻜㻚㻝㻞㻡 㻟㻚㻟㻤
㻠 㻜㻚㻣 㻜㻚㻝㻠 㻟㻚㻤㻢
㻡 㻜㻚㻤 㻜㻚㻝㻡 㻠㻚㻤㻡
㻢 㻝 㻜㻚㻝㻤 㻡㻚㻤㻞
㻺㻿㻾㻵
㻿㻵㻱㻾㻝㻜㻙㻝㻣 㻿㼃㻝㻜㻝㻣
㻿㻵㻱㻾㻞㻜㻙㻟㻜 㻿㼃㻞㻜㻟㻜
㻿㼔㼍㼜㼑㻌㼛㼒㻌㼟㼏㼞㼑㼣㻌㼔㼑㼍㼐
㻼㼍㼚㻌㼔㼑㼍㼐
㼎㼕㼚㼐
㻲㼘㼍㼠
㼔㼑㼍㼐
㻯㼛㼡㼚㼠㼑㼞
㼟㼡㼚㼗
㼔㼑㼍㼐
㼔㼑㼤㼍㼓㼛㼚
㼒㼘㼍㼚㼓㼑
㼎㼛㼘㼠