Oerlikon CENTER ONE Скачать руководство пользователя

Страница: 53 / 102

Operation

GA 09.033/6.02 – (2011-07) –

Oerlikon Leybold Vacuum

4.6.1 Operation

In the Test mode, the following commands are possible:

Selecting a test program

The name of the parameter is displayed as
long as the key is pressed or at least for 2 s.

Program version (

→

53)

Watchdog error (

→

54)

Torr lock (

→

54)

Parameter setup lock (

→

54)

The name of the test program is displayed until
it is started.

RAM test program (

→

55)

EPROM test program (

→

55)

EEPROM test program (

→

56)

Display test program (

→

56)

A/D converter test program channel 0 (

→

57)

A/D converter test program channel 1 (

→

57)

A/D converter test program channel 2 (

→

58)

I/O test program (

→

59)

RS232C test program (

→

60)

Stopping the test program

Starting the test program

Содержание CENTER ONE







































































































Результаты поиска

Содержание CENTER ONE

Отзывы:

Похожие инструкции для CENTER ONE

Бренды по названию

Популярные бренды

Oerlikon CENTER ONE, Руководство по эксплуатации

Результаты поиска

Содержание CENTER ONE

Отзывы:

Похожие инструкции для CENTER ONE

Бренды по названию

Популярные бренды