Odyssey ODY-5 Скачать руководство пользователя страница 29

Страница: 29 / 36

Cast Weight Stack

(Five) - 5 Lb.
Weight Plates

(Nine) - 10 Lb.
Weight Plates

(Five) - 15 Lb.
Weight Plates

Top Plate/

Selector Bar

Fig. 73

The illustration above depicts the

New Cast Weight Stack

Carefully begin sliding the

Weight Plates

over the Guide Rods beginning

with five

15 Lb. Weight Plates

at the bottom, the nine

10 Lb. Weight

Plates

in the middle and then the five

5 Lb. Weight Plates

at the top, as

illustrated above. Furthermore, if the

Weight Stack Decals

have not

been pre-assembled by the factory, then attach them to their respective

Weight Plates

in the order as illustrated above. Continue with

Fig. 74

for

the assembly of the

Selector Pin w/ Coil

Selector Pin w/ Coil

Fig. 74

After the

Weight Stack

has been completely assembled, at-

tach the

Selector Pin w/ Coil

onto the

Top Plate/ Selector Bar

, as illus-

trated above.

Top Plate/

Selector Bar

Selector Pin

w/ Coil

Pec Dec Swivel Handles’ (#8) assembly

AP-250S Cast Weight Stack

Fig. 72

The illustration above depicts the proper assembly of the

Pec

Dec Swivel Handles (#8).

ODY-5 Odyssey Home Gym

105

115

125

140

155

170

185

200

Содержание ODY-5





































Результаты поиска

Содержание ODY-5

Отзывы:

Бренды по названию

Популярные бренды

Odyssey ODY-5, Руководство пользователя

Результаты поиска

Содержание ODY-5

Отзывы:

Бренды по названию

Популярные бренды