Odyssey ODY-5 страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 36

background image

FIG. 32

Next, thread a

Adjustable Stopper (#33)

into the threaded

socket located on the

Top Pulley Housing (#5)

, as shown in left picture

above. Next, insert another

Adjustable Stopper (#33)

into the receptacle

located on the

Front Upright (#3)

and secure it into place using one Flat

Washer SAE 1/2" (#70) and one Regular Nut 1/2-13 (#80), as shown in
right picture above.

Loosely Fasten

: Do not completely fasten this hardware assembly

at this time, as it will be completely fastened later in the assembly

process.

FIG. 31

Attach the

Adjustable Pulley Bracket (#36)

through the hole

on the

Top Pulley Assembly (#5)

and secure it into place at the top

using one Flat Washer SAE 1/2” (#70) and one Nylon Insert Lock Nut 1/2-
13 (#79).

Loosely Fasten

: Do not completely fasten this hardware

assembly at this time, as it will be completely fastened later in the

assembly process.

LOOSELY FASTEN

LOOSELY FASTEN

FIG. 33

Locate the two

Closed-End Double Pulley Brackets (#26)

and attach four Nylon Pulleys 4 1/2 Rd. (#64-Labeled I,V,Q,T). Secure
them into place using four Hex Head Cap Screws 3/8-16 X 1 3/4 (#93),
eight Flat Washers SAE 3/8” (#71) and four Nylon Insert Jam Lock Nuts
3/8-16 (#82). Next, locate the two

Adjustable Double Pulley Plates

(#27)

, as shown above at the right, and attach two Nylon Pulleys 4 1/2

Rd. (#64-Labeled O,X). Secure the pulleys into place using two Hex
Head Cap Screws 3/8-16 X 1 3/4 (#93), four Flat Washers SAE 3/8” (#71)
and two Nylon Insert Jam Lock Nuts 3/8-16 (#82).

FIG. 34

Begin routing the

Lat Cable (#37).

First, remove the Nylon

Pulley 4 1/2 Rd. (#64- Labeled B). Then, route the end of the

Lat Cable

(#37)

up and over the Nylon Pulley 4 1/2 Rd. (#68- Labeled A), then

through the tube of the

Top Pulley Assembly (#5)

. Then, pull the

Lat

Cable (#37)

down where the Nylon Pulley 4 1/2 Rd. (#64- Labeled B) was

once attached.

Next, using the same hardware, re-attach the Nylon

Pulley 4 1/2 Rd. (#64- Labeled B) with the

Lat Cable (#37)

to the

Top

Pulley Assembly (#5)

. Be sure the

Lat Cable (#37)

is routed properly

into the groove on the Nylon Pulley 4 1/2 Rd. (#64- Labeled B).

Note

: Refer to the Cable Mapping Diagram on page 21 for further

detailed illustration of the

Lat Cable (#37)

routing.

ODY-5 Odyssey Home Gym

10

Owner’s Manual: Assembly Instructions

«
...
9
10
11
12
13
...
»

Содержание ODY-5





































Отзывы:

Нет отзывов

Похожие инструкции для ODY-5

Pro 9545 WESY95450

Бренд: Weider Страницы: 16

Бренд: Hoist Fitness Страницы: 53

Iron Grip Strength IGS-412

Бренд: Impex Страницы: 10

Iron Grip Sport IGS-05

Бренд: Impex Страницы: 11

Бренд: Impex Страницы: 14

COMPETITOR WM-343

Бренд: Impex Страницы: 11

Бренд: Impex Страницы: 14

BE STRONG. NS 600X

Бренд: Nautilus Страницы: 22

Бренд: Impex Страницы: 25

XR 7.9 GGBE6969.2

Бренд: Gold's Gym Страницы: 16

CARDIOBULL RA16

Бренд: AsVIVA Страницы: 42

Бренд: ParaBody Страницы: 2

Бренд: Finer Form Страницы: 8

Бренд: Finer Form Страницы: 82

AXIS Bodyweight Trainer

Бренд: Batca Страницы: 24

Бренд: Action Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды