background image

A

bout the Odyssey 5 Home Gym (ODY-5)

Congratulations on your new purchase of the Odyssey 5 Home
Gym (ODY-5). This gym is capable of a variety of different
exercises, as well as, smooth and user-friendly adjustment
features. In addition, this gym has been designed to meet the
needs and performance requirements for a suitable home exercise 
machine. We hope you are completely satisfied with this product 
and wish you many years of enjoyment.

T

uff Stuff Equipment

This Tuffstuff product has been built to precise  quality standards 
and has been carefully packaged to ensure that damage will not 
occur during shipment. The Home Lifetime Warranty and signature
indicating final inspection has been conducted by our line foreman, 
is an expression of our confidence in the completeness, the
materials, and workmanship of this product.

W

arranty

SEE A COPY OF WARRANTY ON BACK PAGE.

R

egistration Card

To avoid unnecessary delays in warranty service and to insure that 
a permanent record of your purchase is on file with our factory, be 
sure to complete the warranty registration card and send it to Task 
Industries today.

A

Note

  provides information necessary to properly

complete a procedure or information which will make 
the procedure easier to understand.

A

Caution

provides a special procedure or special

steps which must be taken while completing the
procedure where the 

Caution

 is found. Not following 

a

Caution

 can result in damage to the equipment. 

A

Warning

provides a special procedure or special

steps which must be taken while completing the
procedure where the 

Warning

is found . Not following 

a

Warning

 can result in personal injury.

 A

ssembly Notes

1. Read and follow each step of this Assembly Instruction Manual in 

sequence. Do not skip ahead, as it will result in an improper
assembly or in having to disassemble parts later.

2. During the assembly of this unit you will be instructed to leave 

some Hex Head Cap Screws loosely fastened. Naturally, they 
will be fully fastened later in the assembly process. This is done 
to prevent any difficulty with alignment of some parts during this 
assembly.

Loosely Fasten

provides a instruction to loosely

fasten (

ex:

hand tighten

) a hardware assembly only. 

This instruction is intended for the alignment of

hardware components during the assembly process.

Fully Fasten 

provides a instruction to fully fasten 

  (

ex:

completely tighten

) a hardware assembly. 

Hardware Measurement Diagram

1

A

bout the Icons

The icons displayed in this Owner’s Manual are used to facilitate 

the correct assembly and safe use of this Product, as-well-as to 

prevent injury to yourself or anyone else. 

LOOSELY FASTEN

F U L L Y   F A S T E N

Introduction

This will notify you of lifting heavy components. It is 
advisable to lift with your legs, not with your back, to 
avoid a possible back injury.

WARNING

ODY-5  Odyssey Home Gym

Note:

Due to continuing product improvements, specifications and designs are subject to change

without notice.

Even though we have prepared this manual with extreme care, neither the publisher nor the  author 
can accept responsibility for any errors in, or omission from, the information given. 

P

rior to the Assembly of the ODY-5

1. We advise you to consult your local Tuff Stuff retailer if you

should have a question or problem regarding the proper
assembly of this Odyssey 5 Home Gym (ODY-5).

2. Consider the complete surface area of the ODY-5. Use the

overhead view on the front page for designing your layout before 
assembling. Once the ODY-5 has been fully assembled it will be 
heavy and difficult to move, therefore you should assemble the 
ODY-5 in the area where it is to be used upon completion.

3. It is recommended that another person assist you with the

assembly this unit. 

4. Neatly organize and identify all parts according to the Parts List 

on page 25 and the Exploded View Diagram on page 24.

T

ool Requirements

1. One 9/16” combination wrench
2. One 3/4” combination wrench
3. One 7/8” combination wrench
4. Two 7/16” combination wrenches
5. One 1/2” combination wrench
6. One ratchet
7. One 9/16” socket
8. One 3/4” socket
9. One rubber mallet 

10. External retaining-ring pliers 
11. Windex or household glass cleaner
12. One can silicone spray/ teflon spray lubricant
13. Multi-purpose grease
14. Measuring tape
15. Masking tape
16. Utility knife

S

pecifications

1. Maximum Wt. Capacity 

- 200 Lbs. Fixed

2. Total Machine Weight 

- 475 Lbs.

3. Footprint (LWH)

- See Front Cover

Содержание ODY-5





































Отзывы: