Oce TDS100 Скачать руководство пользователя | Manualshive

Страница: 22 / 70

background image

22

User manual

Turn on and off the Océ TDS100

Introduction

When you turn on the Océ TDS100, you can use the Océ TDS100 immediately.
After you finished your copy job, you can leave the Océ TDS100 on, because
the Océ TDS100 turns into the sleep mode within two minutes. The power use
is very low in the sleep mode. You can recognise the sleep mode when only the
green light on the operator panel illuminates and the other indicators are off.

The Océ TDS100 activates from the sleep mode when you do one of the
following.

■

Feed an original

■

Feed the media manually

■

Push a key on the operator panel

■

Open a roll unit.

Illustration

[5] The On / off switch at the back of the Océ TDS100

[5] The On / off switch at the back of the Océ TDS100

How to turn on the Océ TDS100

1.

Set the On / off switch at the back of the Océ TDS100 to position 1.

Result

The green light at the operator panel illuminates and indicates that the Océ
TDS100 is in sleep mode.

«
...
20
21
22
23
24
...
»

Содержание TDS100







































































Отзывы:

Нет отзывов

Похожие инструкции для TDS100

CopyCentre C32 Color

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 27

C123 Copycentre

Бренд: Xerox Страницы: 3

C123 Copycentre

Бренд: Xerox Страницы: 28

Бренд: Xerox Страницы: 2

Бренд: Ricoh Страницы: 389

DCP 385C - Color Inkjet - All-in-One

Бренд: Brother Страницы: 256

DCP 385C - Color Inkjet - All-in-One

Бренд: Brother Страницы: 529

Бренд: Panasonic Страницы: 41

Бренд: Toshiba Страницы: 110

SmartLink e-STUDIO16

Бренд: Toshiba Страницы: 252

DocuColor DocuColor 4

Бренд: Xerox Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды